JVC 70 Series User Manual

o-1
GETTING STARTED
Changing and Inserting Batteries.
Use only size AAA batteries.
i Raise the latch on the remote's back cover to remove it.
B Insert the two supplied AAA batteries, carefully noting the “+”
and “" markings on the batteries and remote control. To
avoid a short circuit, insert “—” end first.
EJ Snap the cover back into place.
NOTES:
€) Once the batteries are in the remote and you have con-
firmed that the remote is working, you must program the
remote to operate your particular brand of VCR and/or cable
box. Turn to page 12 now and follow the instructions.
C1 If it takes more than a minute to change the batteries, you may have
to reprogram the CATV and/or VCR codes described on page 12.
MENU
Cif the remote control acts erratically, replace the batteries. Battery
life is usually six months to one year.
O We recommend the use of alkaline batteries for longer battery life.
RM-C732
ONSCREEN HELP!
Onscreen Help is an instruction book built right into the TV. For every Super Command menu item
there is a help screen taht you activate simply by pressing the Hetp button on the remote control.
If you forget how to operate a feature in the menu, go to that feature, press the HELP button, and a
description of exactly what to do appears onscreen. Press HELP again and you return to where you
were in the menu.
(If you don’t know what a particular feature is, go to that feature in the menu, press Help, and a
description of that feature appears onscreen. Press Hetp again to continue.
GETTING STARTED ([i
POWER
O
Make
sure
that
the
TV/CATV
switch
is
set
to
TV.
Switch
to
CATV
only
if
you
plan
to
operate
a
cable
box.
©)
Press
the
Power
button
on
the
remote
control
or
the
TV
front
panel.
The
On-Timer
lamp
will
glow
red.
0
To
turn
the
power
off,
press
the
Power
button
again.
The
On-Timer
lamp
will
go
out.
©
The
On-Timer
lamp
remains
on
while
the
On/Off
Timer
function
is
active
(see
page
19).
ADJUSTING VOLUME
Press the VoLUME button on the front panel or remote control. The volume slidebar will appear.
B
Press
the
Mute
button
to
instantly
turn
the
volume
off.
To
restore
the
volume
to
the
previous
level,
press
the
Mute
button
again.
CHANGING CHANNELS
El 10 Key Direct Access.
* Press the numbers on the remote’s 10 key pad.
¢ For single-digit channel numbers press 0, then the number.
© For channels above 100, press the 100+ button plus the 2-digit number.
FJ Cuannet -/+ Hyrer Scan button.
The CHANNEL / HyPER SCAN button has two levels:
* To scan the channels one at a time, press the remote control's CHANNEL/HYPER SCAN
button to the first level. The channels will scan at about one per second.
¢ To scan the channels really, really fast, press the remote control’s CHANNEL/HYPER SCAN
button to the second level and the channels will rip by at a blazing five per second.
Hi Return.
Press and release the RETURN+ button to return to the previous channel. First, select a channel
(e.g. game #1). Then, select another channel (game #2) with the 10 key pad and push the
Return+ button to flip directly back and forth.
ga Return+.
Press and hold down the ReTurN+ button for three seconds. The message, “RETURN CHANNEL
PROGRAMMED !” will appear and you can scan as you wish. Press RETURN+ again and you will
go back to the Return+ channel.
To cancel a Return+ channel, press and hold down the ReTurn+ button for another three seconds
and the message, “RETURN CHANNEL CANCELLED !” appears.
O Pressing a number key or turning the set off will also cancel a Return+ channel.

JVC 70 Series Specifications

General

Brand	JVC
Model	70 Series
Category	TV
Language	English