JVC ca-mx55mbk - Tape Deck: Basic Operation; Playing and Ejecting Tapes; Playback Direction and Mode Selection

Using
the
Tape
Deck
~
The
tape
deck
has
an
Auto
Tape
Select
feature,
which
can
tell
the
difference
between
various
types
of
cassette
tape.
It
can
distinguish
between
Normal
(Type
1)
and
Cr,
-
High
Position
(Type
Il).
Playing a Tape
1.
Press
the
EJECT
button
to
open
the
cassette
holder.
2.
Insert
a
cassette
and
shut
the
cassette
holder.
3.
If
the
tape
was
recorded
with
Dolby
B
noise
reduction,
press
the
DOLBY B NR switch.
The indicator light will go on.
*
Dolby
noise
reduction
manufactured
under
license
from
Dolby
Labora-
tories
Licensing
Corporation.
“DOLBY”
and
the
double-D
symbol
1
are
trademarks
of
Dolby
Laboratories
Licensing
Corporation.
4.
Start
playback
by
either
of
the
following
methods:
(Deck
B
only)
¢
Press
the
<J
or
tf
button.
Press
the
t>
button
if
the
tape
is
wound
mostly
on
the
left
side.
TE) [a
*
Select
TAPE
with
the
SOURCE
SELECTOR
button
on
the
amplifier.
Note:
*
When
cassettes
are
in
both
decks
A
and
B,
deck
B
starts
first.
Stopping
Playback
and
Ejecting
the
Tape
4.
Press
the
STOP
button
on
the
tape
deck.
2.
Press
the
EJECT
button
to
open
and
remove
the
tape
from
the
cassette
holder.
3. Shut the cassette holder.
Note:
+
If
the
system
is
turned
off
while
a
tape
is
playing,
you
may
not
be
able
to
eject
the
tape.
You
will
need
to
turn
the
system
back
on
and
press
the
EJECT
button
to
open
the
cassette
holder.
Stopping
and
Restarting
Playback
1.
Press
the
PAUSE
button
on
the
tape
deck.
Ou
Playback
of
the
tape
in
deck
B
stops
temporarily.
Note: ;
*
The
PAUSE
button
only
applies
to
deck
B.
CA-MXSSMBK
2. Press the <j or > button.
The restarts playback of the tape in deck B.
Changing the Playback Direction (Deck B only)
1. To change the playback direction during playback, press
the <j or [> button.
The other side of the tape will now play.
2. Tochange the playback direction without starting playback, press
the <] or > button while also pressing the stop Ml button.
Fast-Winding the Tape
Press the <4 or b> buttons on the Tape Deck to advance the tape rapidly
in the direction of the arrows.
REV. mode selection
Press the REV. MODE button and select the replay mode.
Ifthe REV. MODE button indicator is off, the non-reverse mode is effective.
If you press the REV. MODE button and turn the indicator on, the reverse
mode will become effective.
Non Reverse mode
The tape on deck A and the tape on deck B are played. continuously and °
repeatedly in the direction of the arrow ( t ). =.
When playing of the tape on deck A ends, then that of the tape on deck B
will start automatically. When playing of the tape on deck Bbegins, the tape
on deck A will be automatically rewound.
When playing of the tape on deck Bends, playing of the tape on deck A will:
begin automatically. When playing of the tape on deck A begins, the tape
on deck B will be automatically rewound. ~
Reverse mode
One
side
of
the
tape
on
deck
A
and
the
both
sides
of
the
tape
on
deck
B
are
played
continuously
and
repeatedly.
When playing of the tape on deck A ends, playing of the tape on deck B will
begin automatically. When playing of one side of the tape on deck B ends,
the other side of the tape on deck B will be automatically played. When
‘playing of the both sides of the tape on deck B ends, playing of the tape on
deck
A
begins
automatically.
The
tape
on
deck
A
is
rewound
automatically
when deck B starts playing.
1. Insert cassettes Into decks A and B.
2. Press the REV. MODE button and select the REV. mode.
3.
Press
the
¢>
button
on
deck
A
or
the
<]
or
¢>
button
on
deck
B.
* When youselect TAPE with the SOURCE SELECTOR on the amplifier,
deck B starts first.
Music Scanning
The music scan function will detect the blank segments between tracks.
The blank should be about 4 seconds long for the music scan to be
effective.
You
can
locate
the
beginning
of
the
current
track
or
next
track
quickly
by
pressing
the
playback
button
and
the fast-winding
button
simultaneously.
15
(No. 20342) 17