JVC ca-mx55mbk - Advanced Timer and Sleep Functions; Timer Activation and Resetting; Wake-Up and Sleep Timer Operation

CA-MX55MBK |
2. Press the MEMORY button.
This stores the volume level for timed playback or recording in memory.
To change your selection, press the CANCEL button and enter a new
value.
Starting the Timer
Press the Timer button to start the timer. The timer you chose should light
on the display.
Note:
Ifthe timer light does not light, the timer was not set properly, and you
need to set the start time again.
To change your selection, press the CANCEL button and enter a new
value.
Turning the System Off
Press the POWER button on the amplifier to turn the system off.
enon
* The system is now programmed to turn on at the preset start-time, and
play or record until the stop-time.
_¢ Itwill record or play the preset source at the preset volume level until
the top-time is reached.
+ Ifyou turn the system on before the start-time, the timer will still operate
as programmed at the start-time.
Resetting the Timers
To reset a timer, press the button (TIMER 1, TIMER 2, or DAILY) on the
Tuner twice. Now the timer is set again and will use the same start-time,
stop-time, source, and volume level as before.
Setting the Wake-Up and Sleep Timer
You can set a timer so it turns on to wake you up or turns off when you go
to sleep.
Setting the Wake-Up Timer
The wake-up timer serves as an alarm clock. It turns the system on after
a programmed time lapse and plays the source that was used before the
system was turned off. You can seta wake-up time from between 5 minutes
and 12 hours.
1. Press the POWER switch on the amplifier so It Is off.
2. Press the WAKE UP/SLEEP button on the Tuner.
This tells the system that you are going to set the wake-up time.
3. Press the WAKE UP/SLEEP button repeatedly until the desired
wake-up time appears.
WAKE UP/SLEEP
- Each time you press the WAKE UP/SLEEP button, the wake-up time
lapse changes in the following order:
+0:05--0:10-+0:15-70:30-70:45 +1 00+ 1:30 +2:00 -3:00->(every
hour)->12:00— (back to the beginning)
* {f you make a mistake, press the CANCEL button on the Tuner and
enter a new wake-up time with the WAKE UP/SLEEP button.
The system will now turn on after this time lapse.
* The wake-up timer has priority over TIMER 1, TIMER 2, and the DAILY
timer.
This means that if the start-time for one of the timers occurs before the
wake-up time, the system will wait until the wake-up time to turn on.
Note:
¢. IfCDis the source that willbe used, playback begins with the first track. .
22
24 (No. 20342)
Setting the Sleep Timer
The sleep timer is used to turn off the system after a specified time lapse.
With this timer you can fall asleep listening to music, knowing that the
system will shut off automatically and not stay on all night. You can set the
sleep timer to turn the system off from between 5 minutes and 2 hours:
1. Press the POWER switch on the Amplifier so It Is on.
2. Start the source you want to listen to.
3. Press the WAKE UP/SLEEP buiton on the Tuner.
WAKE UP/SLEEP
This tells the system that you are going to set the sleep time.
4. Press the WAKE UP/SLEEP button repeatedly until the desired
sleep time appears.
Each time you press the WAKE UP/SLEEP button, the sleep time lapse
changes in the following order:
—0:05--0:10--0:15-70:30--0:45 +1 :00-$1:15-+1 :30-+1 :45-2:00>
(back to the beginning)
«If you make a mistake, press the CANCEL button on the Tuner and
enter a new sleep time with the WAKE UP/SLEEP button.
The system will now turn off after this time lapse.
* The sleep timer has priority over TIMER 1, TIMER 2 and the DAILY
timer.
This means thatif the stop-time for one of the timers occurs before the sleep
time, the system will wait until the sleep time before turning itself off.
Checking the Remaining Time
After setting the wake-up or sleep timer, you can check the time remaining
until the system turns on (wake-up time) or shuts off (sleep time).
Press the WAKE UP/SLEEP button.
The remaining timeis displayed for 5 seconds. Then the clock time appears
again.
Adding More Time
If you want more time before the wake-up timer turns the system on (or the
sleep timer turns the system off), follow these steps:
1. Press the WAKE UP/SLEEP button.
The remaining time is displayed for 5 seconds. Then the clock time
appears again.
2. Press the WAKE UP/SLEEP button again before the clock time is
displayed.
* Keep pressing this button until the desired additional time is reached.
Now the system will wait until the added amount of time until turning on or
shutting off.
Cancelling the Time Setting
If you decide you don’t wantthe system to wake you up or play music while
you fall asleep, you can turn these timers off.
1. To cancel the wake-up timer, press the POWER button on the
Ampiifier.
This turns the power on.
a om
2. To cancel the sleep timer, press the POWER button on the
Amplifier.
This turns the power off.