JVC HR-D210E - Page 6

;
PLAYING
BACK
A
VIDEO
CASSETTE
|
[
RECORDING
TV
PROGRAMMES
|
BB Turn the TV receiver on and adjust it to your video channel.
Load a pre-recorded cassette.
@ Power will be switched on automatically.
@ When the cassette loaded has no safety tab, playback
will start automatically.
El Press PLAY @.
EllPress STOP @ at the end of the programme.
@ The tape will be rewound automatically when its end is
reached and the recorder will enter the Stop mode.
STILL PICTURE
1. Press PAUSE/STILL @ during playback.
2. To advance the still picture, press PAUSE/STILL a
number of times.
® Keeping this button pressed continuously advances
the picture to give a slow-motion effect.
3. To cancel the Still mode, press PLAY.
Notes:
@ When the Still mode continues for longer than about 5
minutes, the Stop mode will be entered automatically.
@ With some televisions, the still picture may be unstable.
This is not due to any defect of the unit.
SHUTTLE SEARCH
Shuttle Search allows high-speed playback at 9 times
normal speed in either direction.
1. Press either REW or FF SHUTTLE SEARCH ©
during playback.
2. To cancel the Search mode, press PLAY.
®@® For briefer scanning, keep the SHUTTLE
SEARCH button pressed for more than 2
seconds; when you release the button, the
Search mode will be cancelled.
Tracking Adjustment
Noise bars may appear on the screen if you play back a
tape which was recorded using another recorder. For
correction, press either TRACKING control @ . Tracking
will be reset to the preset standard each time the cassette
is ejected.
Safety tab
MB Turn the TV receiver on and adjust it to your video channel.
Load a Cassette (with safety tab in place).
@ Power wilt be switched on automatically.
El Press either TY PROGRAM @ to select the channel you
wish to record.
Press REC/ITR @ to start recording.
®
8e
careful
to
press
REC/ITR
only
once,
or
Instant
Timer
Recording
wil!
begin.
® Press REC and PLAY simultaneously when using the
remote control unit.
@ ‘f there is part of the programme you don’t want to
record, press PAUSE/STILL @.A white horizontal!
bar will appear on the screen, which reduces in size in
4 steps as time elapses. When the last quarter starts
blinking and disappears, the Stop mode will be entered
automatically. The pause duration is possible for about
5 minutes.
Pause mode indicator
# To continue recording from the Pause mode, press
PLAY @ while the white bar is on-screen.
Ef Press STOP @ at the end of the programme.
INSTANT TIMER RECORDING
if you wish for record:
ing to stop automatically
after a certain period of
time, use this Instant Timer Recording mode.
1. Press REC/ITR during recording (or twice if in the
Stop mode).
@ The FDP shows “REC STOP 0:30”, showing that
recording will automatically stop and power will
switch off after 30 minutes.
2. Adjust the switch-off time, if necessary.
®@ Press REC/ITR to increase it in 30-minute incre-
ments {possible up to 4 hours).
@ Use SELECT and SET to set to a more precise time
when required (possible up to 4 hours 59 minutes).
After setting the time, press SELECT so that all
digits stop blinking.
REC STOP
RECORDING ONE PROGRAMME WHILE WATCHING
ANOTHER
A programme not being viewed can be recorded while you
enjoy another programme.
@ Select the channel you wish to record with the
recorder’s TV PROGRAM buttons.
a
=
n
<We
;
®
Select
the
channel
you
wish
to
view
with
the
TV
“
@wEeo
en
the
end
of
the
tape
is
reached
during
recording,
receiver’s
channel
selector.
2
oO
Es
the
tape
is
automatically
rewound
and
stops.
ofe:
Prod
in
Only
SP
(Standard
Play)
recordings
can
be
played
back.
2
=
08
ra
$
Notes:
25
bs
<=
roe
©
If
you
want
to
start
recording
from
the
Play
mode,
first
=.
R23
ai
p=
=
engage
the
Record-Pause
mode
by
pressing
PAUSE/
9325
STILL,
and
then
REC/ITR.
Then
press
PLAY,
3
x
To)
BY
=
=
@
When
recording
is
restarted
from
the
Pause
mode,
a
few
=
=
Db
=
wo
trames
recorded
betore
are
erased
due
to
overlap
of
the
new
z
aoe
©
yd
recording.
This
ts
not
due
to
any
defect
of
the
unit.
b=
|
rs
5
mr
oO
@
The
selected
channel
cannot
be
altered
during
recording.
If
BSBam
3
2
=
you
wish
to
change
the
channel,
first
engage
the
Pause
&
MY
2
o
ge
mode
and
then
select
a
different
channel.
mM