JVC KD-R710 - User Manual

6 pages

Save Page as PDF

To Next Page

KD-R710

CD RECEIVER : INSTRUCTIONS

1209DTSMDTJEIN

GET0647-001B

[J]

1 Turn on the power.

Canceling the display demonstration

4 Select <DEMO OFF>.

6 Finish the procedure.

Setting the clock

1 Turn on the power.

3 Select <CLOCK>.

4 Select <CLOCK SET>.

5 Adjust the hour.

6 Adjust the minute.

7 Finish the procedure.

Preparations

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car...

If you have parked the car for a long time in hot or

cold weather, wait until the temperature in the car

becomes normal before operating the unit.

Basic operations

When you press or hold the following button(s)...

Main unit

Remote

controller

General operations

Turns on.

• When the power is on, pressing

/I/ATT on the remote controller also mutes the

sound or pauses. Press

/I/ATT again to cancel muting or resume playback.

Turns off if pressed and held.

Selects the available sources (if the power is turned on).

• If the source is ready, playback also starts.

Adjusts the volume level.

• Selects item if turn the control dial on the main unit.

—

• Mutes the sound while listening to a source. If the source is “CD,” “USB FRONT/

USB REAR,” or “IPOD-FRONT/IPOD-REAR,” playback pauses. Press the control dial

again to cancel muting or resume playback.

• Enters playback mode menu directly if pressed and held.

• Confirms selection.

Selects the sound mode.

• Enters tone level adjustment directly (see page 4) if pressed and held EQ BASS-TRE

on the main unit.

—

• Enters “Call Menu” screen or answers incoming call when the unit rings.

• Ends a call if pressed and held.

—

Power off : Checks the current clock time.

Power on : Changes the display information.

For Bluetooth operations, see pages 2 to 4.

• Microsoft and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation

in the United States and/or other countries.

• “Made for iPod” means that an electronic accessory

has been designed to connect specifically to iPod

and has been certified by the developer to meet

Apple performance standards.

• “Works with iPhone” means that an electronic

accessory has been designed to connect

specifically to iPhone and has been certified by the

developer to meet Apple performance standards.

• Apple is not responsible for the operation of this

device or its compliance with safety and regulatory

standards.

• iPod is a trademark of Apple Inc., registered in the

U.S. and other countries.

• iPhone is a trademark of Apple Inc.

• The Bluetooth word mark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks

by Victor Company of Japan, Limited (JVC) is under

license. Other trademarks and trade names are

those of their respective owners.

Warning:

If you need to operate the unit while driving, be sure

to look around carefully or you may be involved in a

traffic accident.

Caution on volume setting:

Digital devices (CD/USB) produce very little noise

compared with other sources. Lower the volume

before playing these digital sources to avoid

damaging the speakers by the sudden increase of

the output level.

(Initial setting)

[Hold]

(Initial setting)

[Hold]

Control dial

Loading slot

Display window Auxiliary input jack

Ejects the disc

Detaches the panel

USB (Universal Serial

Bus) input terminal

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.

(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly

with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to

ensure your complete understanding and to obtain the

best possible performance from the unit.

For customer Use:

Enter below the Model No. and

Serial No. which are located

on the top or bottom of the

cabinet. Retain this information

for future reference.

Model No.

Serial No.

Remote sensor

• DO NOT expose to bright sunlight.

Returns to the previous menu

How to attach/detach the control

panel

How to reset your unit

Reset the unit after installation is

completed.

• Your preset adjustments will

also be erased (except the

registered Bluetooth device,

see page 3).

How to forcibly eject a disc

• You can forcibly eject the loaded disc even if the

disc is locked. To lock/unlock the disc, see page 2.

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

Preparing the remote controller

(RM-RK50)

When you use the remote controller for the first time,

pull out the insulation sheet.

If the effectiveness of the remote controller

decreases, replace the battery.

Replacing the lithium coin battery

For USA-California Only:

This product contains a CR Coin Cell Lithium Battery

which contains Perchlorate Material—special

handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Caution:

• Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent

type.

• Battery shall not be exposed to excessive heat such

as sunshine, fire, or the like.

Warning (about battery handling)

To prevent accidents and damage:

• Do not install any battery other than CR2025 or its

equivalent.

• Store out of reach of children.

• Do not recharge, short, or dismantle.

• Do not dispose of in fire.

• Do not carry around with other metallic materials.

• Wrap the battery with tape and insulate when

throwing away or saving it.

[Hold]

Insulation sheet

CR2025

[European Union

only]

EN_KD-R710[J]ff.indd 1EN_KD-R710[J]ff.indd 1 1/6/10 12:59:29 PM1/6/10 12:59:29 PM

Main Page

Questions and Answers

J
john54Aug 25, 2025
Why is there static noise on my JVC KD-R710 radio?
- V
  Vincent KellerAug 25, 2025
  If you are experiencing static noise while listening to the radio on your JVC Car Receiver, ensure the antenna is firmly connected.
R
Robert WilsonAug 25, 2025
Why won't my JVC KD-R710 Car Receiver detect bluetooth?
- V
  Valerie MartinAug 26, 2025
  If your JVC Car Receiver is not detecting the Bluetooth device, try searching for it again from the Bluetooth device. If that doesn't work, reset the unit and then search again from the Bluetooth device.
A
Angela MaddoxAug 26, 2025
What to do if “PROTECT” appears on JVC KD-R710 Car Receiver?
- M
  Michael NelsonAug 26, 2025
  If the JVC Car Receiver displays “PROTECT” and no operations can be performed, ensure the terminals of the speaker leads are properly covered with insulating tape. Then, reset the unit. If the issue persists, it is recommended to consult a JVC car audio dealer or a company supplying kits.
A
Anna AdamsAug 27, 2025
Why does my JVC Car Receiver skip during Bluetooth playback?
- V
  Vanessa BaxterAug 27, 2025
  If the sound is interrupted or skipped during playback of a Bluetooth audio player on your JVC Car Receiver, try the following: 1. Reduce the distance between the unit and the Bluetooth audio player. 2. Disconnect the device connected for Bluetooth Phone. 3. Turn off, then turn on the unit. 4. If the sound is still not restored, connect the player again.
L
lauramartinezAug 27, 2025
How to reduce echo on JVC Car Receiver?
- D
  David HughesAug 27, 2025
  If you are experiencing echo or noise with your JVC Car Receiver, try adjusting the microphone unit’s position.
G
Gregory RiosAug 28, 2025
Why is the phone sound quality poor on my JVC Car Receiver?
- A
  Andrea CarrollAug 28, 2025
  If you are experiencing poor phone sound quality with your JVC Car Receiver, try reducing the distance between the unit and the Bluetooth mobile phone. Alternatively, move the car to a location where you can get better signal reception.
L
lynngaryAug 29, 2025
Why can't I select AM AUX or BT AUDIO on my JVC Car Receiver?
- C
  Craig WatsonAug 29, 2025
  If “AM,” “AUX IN,” or “BT AUDIO” cannot be selected on your JVC Car Receiver, check the setting.
D
Daniel GonzalesAug 30, 2025
What to do if JVC KD-R710 Car Receiver doesn't copy phonebook?
- H
  Hannah JacobsAug 30, 2025
  If the JVC Car Receiver does not respond when you try to copy the phonebook to the unit, it may be because you have tried to copy the same entries that are already stored. Press DISP or BACK to exit.
J
John PierceAug 23, 2025
How to fix sound not working on JVC KD-R710 Car Receiver?
- X
  xhahnAug 25, 2025
  If you can't hear any sound from the speakers, first, adjust the volume to the desired level. Also, ensure that the unit is not muted or paused. Finally, check the cords and connections to make sure they are properly connected.
V
veverettAug 31, 2025
Why won't my JVC KD-R710 play the disc?
- M
  Mark HarrisAug 31, 2025
  If your JVC Car Receiver is unable to play back a disc, ensure that you insert the disc correctly.