JVC KW-AV71BT Installation And Connection Manual

30˚
Monitor panel
KW-AV71BT
KW-AV71BT
1
If necessary,
restore the
protruding tabs.
Parts list for installation and connection
KW-AV71BT
Installation/Connection Manual
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC
car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic
accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal
accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic
accident.
• The driver must not watch the monitor while driving. It may lead to carelessness and cause an
accident.
• If you need to operate the unit while driving, be sure to look around carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback
picture will be shown.
To prevent short circuits, disconnect the battery’s negative terminal and make all electrical
connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
• Be sure any cable is not caught on the car’s chassis or under seats.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.
• It is recommended to connect speakers with maximum power of more than 50 W (both at the
rear and at the front, with an impedance of 4  to 8
Ω).
• To prevent short circuits, cover the terminals of the
UNUSED leads with insulating tape.
• At the time of installation, be sure to fix all wires
(wires both from this unit and from the car itself) in
a way that no wires can come into contact with heat
sinks on the rear and side of the unit.
CAUTION: Install this unit in the console of your vehicle. Do not touch the metal parts of this
unit during and shortly after the use of the unit. Metal parts such as the heat sink and enclosure
become hot.
Heat sink
GET0897-002A
[UI]
1112EHHMDWJEIN
EN
© 2012 JVC KENWOOD Corporation
Round head screws
(M5 x 8 mm)
Flat head screws
(M5 x 8 mm)
Main unit/Trim plate
Wiring harness
Monitor panel and soft case
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to
your specific car. If you have any questions or require information regarding installation kits, consult your JVC
car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could
become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
• You cannot install the unit on the car which has any obstacles in the space shown in “Required space for
installation and the monitor panel ejection” below.
1 Remove the audio system originally installed in the car, together with its mounting brackets.
• Be sure to keep all the screws and parts removed from your car for future use.
2 Attach the mounting brackets (removed from the car) to this unit (see below).
• Use flat head screws or round head screws, depending on installation location.
• When you need to use round head screws, use the supplied screws and the screws used to attach the metal
protection plates to the unit when shipped.
3 Do the required electrical connections.
• See “ELECTRICAL CONNECTIONS” on pages 1 and 2.
4 Install this unit using the screws removed in step 1.
5 Attach the trim plate to the main unit.
6 Attach the monitor panel (see below).
Install the unit at an angle of
less than 30˚.
Connecting the parking brake lead
Parking brake
Parking brake switch
(inside the car)
Parking brake lead
(light green)
To metallic body or
chassis of the car
ELECTRICAL CONNECTIONS
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the wiring harness to the car battery;
otherwise, the unit will be seriously
damaged.
• BEFORE connecting the speaker leads of
the wiring harness to the speakers, check the
speaker wiring in your car.
TROUBLESHOOTING
Supplied
screws
Mounting bracket
removed from the car
Screws removed from the car in step 1
Supplied screws
Select the type of
screws appropriate
for the mounting
bracket.
Step 6
• When you use screws other than those supplied, use 8
mm-long screws. If longer screws are used, they could
damage the unit.
• Tighten the screws firmly to prevent the unit from
falling off.
Locate the reverse lamp lead in the trunk.
Extension wire (not supplied for this unit)
Purple with
white stripe
Reverse lamps
To reverse lamps
Reverse lamp lead
Connecting the reverse gear signal lead (for rear view camera)
• The fuse blows.
* Are the red and black leads connected
correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to
the car’s chassis using shorter and thicker
cords?
• This unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers
grounded in common?
• This unit does not work at all.
* Have you reset your unit?
Remove the metal protection plates from the
unit before installation.
•
Keep the round head screws (M5 x 8 mm)
used to attach the metal protection plates.
You may need to use the screws for
installation.
The following example is for installation
in a Toyota car. For more details,
consult your JVC car audio dealer.
Extension wire (supplied)
Extension wire
Required space for
installation and the monitor
panel ejection
160 91.6
100
20
4
Dashboard
Bag for storing the adapter
Microphone
Bluetooth adapter
(attached)
Trim plate
Step 5
Trim plate
1-2KW-AV71[UI].indd11-2KW-AV71[UI].indd1 12.11.94:00:44PM12.11.94:00:44PM

JVC KW-AV71BT Specifications

General

Audio system	MOS-FET
MP3 playback	Yes
Audio formats supported	MP3, WAV, WMA
Image formats supported	JPG
Supported radio bands	AM, FM
Preset stations quantity	24
Display diagonal	7 \
Display resolution	800 x 480 pixels
Bluetooth profiles	A2DP
Output power	200 W
Product color	Black
TV tuner integrated	No
Disc types supported	CD-R, CD-RW, DVD+R, DVD+RW, DVD-R
Analog signal format system	NTSC, PAL

Weight and Dimensions

Weight	2800 g
Dimensions (WxDxH)	188 x 117 x 10 mm