JVC KW-AVX848 Connect And Set Up

1 page

1 Check the connected cable.

■ To listen to the music: USB 2.0 cable (accessory of the

iPod/iPhone)

■

To iPod/iPhone

USB cable from the

rear of the unit

To watch the video and listen to the music: USB Audio

and Video cable JVC KS-U30 (separately purchased)

Caution

Videos cannot be played if connected with any cable other

than JVC KS-U30.

2 Set <Input> on the unit.

The item to set on the unit varies depending on the

connected cable.

1. Turn off the AV source.

2. Display the <Settings> screen.

3. Display the <Input> screen.

JVC KS-U30

(separately

purchased)

Connections and Settings for Using iPod/iPhone on the Unit Using iPhone Navigation App (MotionX-GPS)

4. When connected with a USB 2.0 cable:

Set <Audio Input> to <AV-IN>.

For KW-AVX848/KW-AVX840/KW-ADV794/

KW-AVX748/KW-AVX740

For KW-AVX640

You can listen to the music.

When connected with JVC KS-U30:

Set <Audio Input> and <Video Input> to <iPod>.

For KW-AVX848/KW-AVX840/KW-ADV794/

KW-AVX748/KW-AVX740

For KW-AVX640

You can watch the video and listen to

the music.

EN / SP / FR / PT

LVT2312-002A

[J/JW]

For Americas

1 Confirm that the unit is connected with JVC

KS-U30 (separately purchased).

MotionX-GPS cannot be used if connected with any cable

other than JVC KS-U30.

2 Change the settings for using MotionX-GPS.

1. Turn off the AV source.

2. Set <Input> on the unit.

JVC KS-U30

(separately

purchased)

Set <Audio Input> and <Video Input> to

<iPod>.

For KW-AVX848/KW-AVX840/KW-ADV794/

KW-AVX748/KW-AVX740

For KW-AVX640

3. Display the “

iPod

” source control screen.

4. Display the <Mode> screen.

5. Set <iPod Control> to <External>.

3 Start MotionX-GPS from your iPhone.

4 Select “

iPod

” as the source.

The map displayed on the connected iPhone appears on

the unit’s display.

Caution

MotionX-GPS cannot be operated on the unit. Use iPhone to

operate it.

• iPod and iPhone are trademarks of Apple Inc., registered in

the U.S. and other contries.

KW-AVX848 / KW-AVX840

KW-ADV794 / KW-AVX748 / KW-AVX740

KW-AVX640

Notice_sheet.indd 1Notice_sheet.indd 1 11/07/01 14:1411/07/01 14:14

Other manuals for JVC KW-AVX848

Instruction Manual215 pages

Installation & Connection Manual6 pages

Questions and Answers:

K
Karl MillerAug 23, 2025
Why no sound from speakers on my JVC Car Receiver?
- P
  Patrick CombsAug 23, 2025
  Ensure the volume is at an audible level and check all cords and connections.
A
Alexandria ArcherAug 31, 2025
Why does my JVC Car Receiver say 'Parking Brake'?
- P
  porteremilySep 1, 2025
  No playback picture is shown when the parking brake is not engaged.
H
hessjesseAug 30, 2025
What to do if my JVC Car Receiver displays 'No Signal'?
- Y
  Yvonne WebbAug 31, 2025
  If you see a 'No Signal' message, start playback on the external component connected to the VIDEO IN jack, check the cords and connections, and ensure the signal input isn't too weak.
C
Crystal StewartAug 29, 2025
Why is there no picture on my JVC Car Receiver screen?
- L
  larry26Aug 29, 2025
  Ensure that the screen is turned on.
A
Andrew JohnsonAug 28, 2025
What does 'USB Device Error' mean on my JVC Car Receiver?
- P
  psavageAug 28, 2025
  A 'USB Device Error' indicates an abnormal USB power voltage. Try turning the unit off and on again. If that doesn't work, try connecting a different USB device.
M
Marisa RosarioAug 27, 2025
How to fix static noise on JVC Car Receiver radio?
- U
  ugregoryAug 27, 2025
  Make sure the antenna is firmly connected.
D
Dalton AdamsAug 26, 2025
What to do if my JVC Car Receiver says 'Miswiring Check wiring connection and then reset unit'?
- D
  Denise GoodmanAug 27, 2025
  This message indicates that a speaker cord has shorted or come into contact with the car chassis. You should wire or insulate the speaker cord appropriately and then reset the unit.
C
Cindy BaileyAug 25, 2025
What to do if power cannot be supplied to the JVC Car accessory through the expansion port?
- S
  scottsmithAug 26, 2025
  If the JVC car accessory isn't getting power through the expansion port, you'll need to connect the power cord that came with the component separately.
A
alexandermargaretAug 25, 2025
Why is there no sound from my JVC Car Receiver when using iPod?
- M
  morganronaldAug 25, 2025
  Try disconnecting the iPod and then reconnecting it. You can also select another source and then reselect “iPod”.

JVC KW-AVX848 Specifications

General

Audio Output Power	50W x 4
RMS Power Output	22W x 4
Bluetooth	Yes
USB Port	Yes
DVD Playback	Yes
HD Radio	No
iPod Control	Yes
Satellite Radio Ready	Yes
Preamp Outputs	3 (Front, Rear, Subwoofer)
CD Playback	Yes
Built-in Amplifier	Yes
Video Output	Yes
Radio Tuner	AM/FM
iPhone Control	Yes
Rear View Camera Input	Yes
Steering Wheel Control Compatible	Yes
Resolution	800 x 480 pixels
Equalizer	13-Band Graphic Equalizer