JVC LT-40HW62U - Schedule List; Chapter 6 - Network Network Connection; Connecting to a Wired Network

EN
16
Note: if you change channels while recording a
programme, a prompt will appear on screen
asking you whether you want to conrm
the channel change. If you do so, your
recording will be interrupted.
4.
In recording, PVR mini pane will also show on the
screen to indicate the recording progress.
5.
To watch the recorded programme, exit PVR mode
rst and go to
Media > Video
. Select the folder
PVR, then select the related record le. Press
OK
to play. (It is the same if you record a digital radio
programme).
Notes:
-
This feature is available only for non encrypted
digital channels. Even when CICAM (CI or
CI+) is inserted, this feature is not available on
encrypted channels.
-
Before you connect the USB drive to the set,
make sure you have backed up the data in the
drive to avoid the loss of your important data due
to unforeseen malfunction.
-
The bigger the USB drive free memory for the
PVR function, the bigger the recording length.
-
If you want to change channel or signal source
during recording, store the recording data before
changing the channel or source.
-
The set cannot play les normally if the
parameters of the le exceed the limitations of
the system, the le format is not supported, the
le is damaged, or the le cannot be decoded.
-
Do not disconnect the USB drive when the
system is reading a le or transmitting data,
otherwise the system or the drive may be
damaged.
Schedule list
This function is used to perform scheduled recording.
Warning: for this operation you have to insert a USB
recording device, otherwise the recording will not
start.
1.
Press
OPTION
on the remote control and in the
Quick access menu, select
Schedule list
.
2.
Press
OK
to display the schedule list.
3.
To add a schedule into your schedule list, press
the red button rst to display
Schedule list
. Then,
-
Channel number:
use
◄/►
to select the
channel number.
-
Start date:
use the alphanumeric buttons to set
the recording date.
-
Start time:
set the start time of the recording.
-
Stop time:
set the stop time of the recording.
-
Schedule type
:
• Set
Reminder
to be reminded that you can
switch to the scheduled programme when the
time you have set comes. When time is out and
you do not execute any operation, the dialogue
box will disappear and no further operation will
be executed.
• Set
Record
, if you really want to start your
scheduled recording when the time you have
set comes. When time is out and you do not
execute any operation, scheduled recording will
start automatically.
-
Repeat type:
set different repeat modes for the
recording.
4.
Press
▲/▼/◄/►
to select
Add
, then press
OK
to
add the schedule you set into your schedule list.
5.
Press the red button to repeat above procedures
to add another schedule.
6.
If you wish to edit or delete a schedule, select it
and press
OK
to enter and follow the instructions
on screen.
7.
Press
EXIT
to close the menu.
Network
Network connection
You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can attach your TV to your LAN using cable in
three ways:
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an external modem
using a Cat 5 cable minimum.
• You can attach your TV to your LAN by connecting
the LAN port on your TV to an IP Sharer, which is
connected to an external modem. Use Cat 5 cable
minimum for the connection.
• Depending on how your network is congured,
you may be able to attach your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable minimum.
Note that the wall outlet is attached to a modem or
router elsewhere in your house.
1.
Press
MENU
on the remote control and select
Network > Network settings > Internet
connection
. Press
◄/►
to select
On
.
2.
Press
▲/▼
to select
Interface
, then set
◄/►
to
Ethernet
to select wired-mode connection.
3.
Press
▲/▼
to select
Connection test
, then press
OK/►
to check the Internet connectivity. If it does
not work, follow step 4 below.
4.
Select
Network > Network settings > IP setting
,
then press
OK/►
to enter the
IP setting
menu.
You can set
Address type
to
Auto
or
Manual
.
- Select
Auto
if you want the TV to acquire and
enter the needed IP address automatically.
- Select
Manual
if you want to enter your IP
address manually, then:
• Press ▼ to go to the rst entry eld.
Chapter 6
Network
Downloaded from www.vandenborre.be