Once you have adjusted the Sun'ound modes, the adjustment is
memorized for each Surround mode.
Dolb V and DTS Surround adjustments
Before you start, remembel=..
• Make sure that you have set the speaker information correctly
(see page 12).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start fi'om step 3 again.
• You cannot adjust the rear speaker output levels when you have set
"REAR SPK" to "NO." See page 12.
• You cannot adjust the center speaker output level when you have
set "CENTER SPK" to "NO." See page 12.
From the remote control:
1. Select and play a sound source.
• To enjoy Dolby Pro Logic, play back a software encoded with
Dolby Surround and labeled with 1312EDOLBYSURROUNO_mark.
• To enjoy Dolby Digital, play back a sof'ware encoded with
Dolby Digital and labeled with BB_ mark.
• To enjoy DTS Digital Sun'ound, play back a software encoded
with DTS Digital Surround and labeled with _ mark.
2. Press SURROUND to activate an
appropriate Surround mode-
PRO LOGIC, DOLBY DIGITAL
or DTS SURROUND.
When "PRO LOGIC" is selected,
the PRO LOGIC indicator lights up on the display.
• Each time you press the button, the Surround mode turns on
and of'["alternately.
Note:
You can also press SURROUND MODE to activate an appropriate
Surround mode -- PRO LOGIC, DOLBY DIGITAL, or DTS.
3. Press SOUND. soo_
The 10 keys are actix ated fbr sound adjustments.
4. Press TEST to check the speaker rEsT
output balance. %
"TEST TONE L" starts flashing on the
display, and a test tone comes out of the
speakers in the lbllowing order:
TEST TONE L _ TEST TONE C _ TEST TONE R
(Left front speaker) (Center speaker) (Right front speaker)
TEST TONE LS. TEST TONE RS, |
(Left rear speaker) (Right rear speaker)
Notes:
* You can adjust the speaker output levels without outputting the
test tone.
* No test tone comes out of the center speaker when "CENTER
SPK" is set to "NO" (see page 12).
* No test tone comes out of the rear speakers when "REAR SPK"
is set to "NO" (see page 12).
5. Adjust the speaker output levels. -eENT_a÷
• To adjust the center speaker level, press
(;ENTER + (from +10 dB to 10 dB).
• To adjust the lef' rear speaker lexel, press %/
REAR.L +/ (fi'om +10 dB to l0 dB). -R_aR.C*
• To adjust the right rear speaker level, press
REAR.R +M (fi'om +10 dB to 10 dB).
6. Press TEST again to stop the test rest
tone. %
On the front panel:
You can also use the buttons on the fi'ont pane] to adjust the
Surround modes. However, no test tone is available when using the
buttons on the fi'ont panel. So, make adjustments while listening to
the sound of the source played back.
.
Select and play a sound source.
• To enjoy Dolby Pro Logic, play back a soft_xare encoded with
Dolby Snn'ound and labeled with DI:]IDoLB_SURaOUND]mark.
• To enjoy Dolby Digital, play back a software encoded with
Dolby Digital and labeled with DB_ mark.
• To enjoy DTS Digital Smronnd, play back a software encoded
with DTS Digital Surround and labeled with _ mark.
. Press SURROUND ON/OFF to SURROUNOON/O_F
activate an appropriate Surround
mode -- PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.
When "PRO LOGIC?" is selected, the PRO LOGIC? indicator
lights up on the display.
• Each time you press the button, the Sun'ound mode turns on
and off ahernately.
.
Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of ADJUST
the following indications appears on
the display.
>_/
"(?ENTER LEVEL":
To adjust the center speaker level.
"REAR L LEVEL":
To adjust the left rear speaker lex el.
"REAR R LEVEL":
To adjust the right rear speaker level.
2) Press CONTROL [P A/DOWN V to CONTROL
DOWN Lip
adjust the selected speaker output level
_l . II--ll
(from+10 to,0
3) Repeat 1) and 2) to adjust the other "-._" )
speaker output levels.
%./
21
To Next Page
Loading...
Need help?
General
