JVC RX-807VTN

(CEEO~ “ON) PHL-L
COMPU LINK Remote. Control System. é
© For audio terminal connections, see ‘‘Audio Component Connections’. PO AADII TEAS
Remote cable for COMPU LINK
CD player
Turntable
JVC's exclusive ‘’COMPU LINK’’ remote control system connects
equipment with JVC COMPU LINK-3/SYNCHRO terminals to the re-
mote control system. The equipment can be controlled from the re-
mote control unit, or other functions (such as automatic source
selection and synchronized recording) can be used
For further details, see the remote control unit description in this
instructions,
® Equipment remote control
By connecting the COMPU LINK-3 SYNCHRO terminal to the receiver,
the equipment that does not have REMOTE SENSOR in its main unit
can be remote controlled via REMOTE SENSOR of the receiver.
= Automatic source selection
Pressing SOURCE SELECTOR keys will automatically put the cor-
responding source equipment into the PLAY mode. When the PLAY
key on source equipment is pressed, the corresponding SOURCE
SELECTOR key is automatically set to that source. Other source equip-
ment shuts down about 5 seconds later.
® Synchronized recording
Synchronized recording permits a tape deck to start recording auto-
matically in synchronism with a CO player or turntable. Set the tape
deck in the REC/PAUSE mode and press the PLAY key on the CD
player or turntable. The tape deck will enter the recording mode au-
tomatically, starting synchronized recording.
Synchronized recording stops automatically after the CD player or
turntable has stopped and the tape deck has entered the REC/MUTE
mode for about 4 seconds.
@ To set the REC/PAUSE mode, press the REC and the PAUSE key
at the same time. Synchronized recording is disabled if the PAUSE
key is pressed after the REC and the PLAY key are pressed simul-
taneously. For details, refer to the tape deck instructions.
= CD auto-changer with COMPU LINK-3 SYNCHRO
terminal
You can turn on/off the CD auto-changer along with the RX-807VTN
by connecting the COMPU LINK-3 SYNCHRO terminal of the CD auto-
changer to the RX-807VTN. For details, refer to the CD Auto-Changer
instructions.
24
i
WoW U bE eTt
Iil/Remote |i
Control System
Cassette deck
(TAPE 1)
Either of these two
COMPU LINK-3
SYNCHRO terminals
can be used
Notes:
@ COMPU LINK remote control does not work on the tape deck con-
nected to the TAPE 2 terminals
If you connect a tape deck to the TAPE 2 terminals, disconnect
the remote control cable
@ if the power for any connected equipment is shut off during syn-
chronized recording, the system will not operate properly. In this
case, you must start all over again
@ During synchronized recording the SOURCE SELECTOR key will
lock in either the CD or PHONO position. This is to prevent you
from accidentally stopping the recording or changing to any other
source. To change to another source you must first stop syn-
chronized recording
@ If you program track numbers on a CD player or CD auto-changer
and use synchronized recording, a blank space about 4 seconds
long will be left between recordings. This permits music scanning
Display examples
When using the remote control unit to operate equipment which has
the COMPU LINK-3/SYNCHRO terminals, the name of the source and
the operating mode will appear on the display
(os! (o>) Les) Po]
Symbol im
1) Ls
ination |W LU elie bio
“REC/PAUSE”’ ]
mode
“'REC/PLAY’”
mode
AV COMPU LINK System ‘
VIDEO input
4
TV for AV COMPU LINK
Le.
MONITOR OUT
terminal
Connecting the AV COMPU LINK terminals on the rear panel to a
JVC video components for AV COMPU LINK will enable one-touch
control of the integrated audio/video system
There are three AV COMPU LINK terminals. To connect a TV, use
the terminal marked '’TV'’. To connect a VCR, use either of the
remaining two terminals
One-touch Video Piayback
Insert an overwrite-protected video tape in the VCR (VCR 1)
The TV, VCR, and the receiver turn on, and the video tape plays back
automatically
« When playing back a video tape that is not overwrite protected
or there is already a video tape inside the VCR, press ‘‘PLAY’’
on the VCR
* The input source selectors of the TV and receiver are automati-
cally selected.
This means that simply loading a tape prepares everything needed
to enjoy videos on your integrated audio/video system.
When you switch the SOURCE SELECTOR of the receiver to VCR
1 or VCR 2, the TV input will also automatically be set to VIDEO.
AV system power ON/OFF
When the receiver is turned off, the TV and VCR are automatically
turned off
When the receiver is turned on, the components which are automat-
ically turned on with the receiver depends on the SOURCE SELECTOR
key settings.
© If the SOURCE SELECTOR keys were set to VCR 1 when the power
was turned off, both the TV and VCR 1 are turned on
* If the SOURCE SELECTOR keys were set to VCR 2 when the power
was turned off, the TV is turned on.
* If the SOURCE SELECTOR keys were set to an audio source when
the power was turned off, only the receiver is turned on.
Remote cable for
AV COMPU LINK AUDIO and
{optional} VIDEO output
aaa |
VCR for AV COMPU LINK
(VCR 1)
* To carry out ‘‘One-touch Video Playback’,
connect the VCR to VCR 1 terminals.
Notes:
© The AV COMPU LINK terminals and the COMPU LINK-3 SYNCHRO
terminals are not the same jack
* If the AV COMPU LINK terminal and the SWAP terminal of the
VCR share the same terminal for connection, select whichever
one you need.
* The AV COMPU LINK terminals must not be connected to any
VCR not made for AV COMPU LINK (whether manufactured by
JVC or not.)
The AV COMPU LINK terminals of the receiver has three jacks
The jack marked TV must be connected to TV.
* For connection, use the shielded audio cable with monaural mini
plug {3.5 mm @) equivalent to the remote cable for COMPU LINK-3
SYNCHRO.
© When operating the TV by remote control, point the remote con-
trol unit at the REMOTE SENSOR of the receiver
(When a remote cable is connected to the AV COMPU LINK
terminals of the TV, REMOTE SENSOR of the TV is disabled.)
« When operating the VCR by remote control,
1. Set the VCR remote control code setting to ‘‘A”’
2. Point the remote control unit directly at the VCR
25
NLAZO8-XU