JVC RX-807VTN

(EEEOT “ON) OL-L
= Storing the Signals of Another Remote Control Unit
Other remote
control
Transmitting window 1
2 to 4 inches
5 to 10 om”
Transmitting-receiving window
28
Signals of other remote controls can be stored with the PROGRAM-
MABLE CONTROL SECTION keys and POWER (TV or VCR} key.
You can control the JVC audio, video, and other remote controll-
able equipment directly from the remote control unit
You can program different signals for the source units selected
with the Equipment Select keys in the PROGRAMMABLE CON-
TROL SECTION keys
Place both remote control units on a flat surface.
Be sure that the transmitter window of the other remote control
unit is about 2~4 inches {5~ 10 cm) from the transmitting-
receiving window. If the units are too close or too far apart,
signals may not be stored properly.
« Press the LEARN key to set this remote control unit to LEARN
mode
Lights
eaan S17
-o- _—
SEND/LEARN ERROR
Be sure not to press the LEARN key strongly with a pointed
article such as a ballpoint pen, otherwise the VCR may be
damaged
2. Seelct the function mode required to be programmed with any
of the Function Select keys
3. Press the desired key for memorizing
Blinks
1 ——s eooL—Joee co
SEND/LEARN ERROR
Continue pressing the key until the SEND/LEARN indicator
begins to blink.
@ |f the ERROR indicator lights when the SEND/LEARN indica-
tor is blinking, the key you pressed already has a function
stored in it. If you continue with the storing procedure, the
previously stored information will be cleared and the new
information will be stored instead. If you want to keep the
previously stored information, select another jearning key and
press it.
4. While the SEND/LEARN indicator is stili blinking, press continu-
ously the key you want to learn on the other remote control unit.
@ If the SEND/LEARN indicator stops blinking before you press
the key on the other remote control unit, begin again from
step 3.
Press the key. OFF OFF
CQ 9 oo (Reading)
SEND/LEARN ERROR
Lights ‘ Lights
-o3a- -Co— (Processing)
7S 7\N
tights $ ofr
-—o- [ ow | {Processing
71s normally)
Keep pressing. @ If the ERROR indicator lights, learning operation
has not been performed correctly.
Repeat the programming procedure again.
@ If the ERROR indicator blinks, it means that
further programming is inhibited. If you want
to program a new signal in a key, cancel the
signal preprogrammed in that key before
retrying the programming operation
OFF t OFF (Completed)
[ wow ] oo
CO
iN
Release the key.
5. When programming is completed, the SEND/LEARN indicator
goes off.
6. Press the LEARN key to reset the remote control unit to USE
mode.
IMPORTANT
@ This unit can learn aimost any remote control signal if the other
unit is an infra-red type remote control unit. However, it may
not be able to learn special signals or very long signals. (If you
repeat the learning procedure several times and the unit still
does not operate properly, it may be due to this kind of
problem.)
© Some remote control transmit a number of instructions simul-
taneously {when programming the timer of a TV/VCR. for ex-
ampie}; in such a case, the unit may not operate correctly
@ When you use the Recording function, be sure you do not ac-
cidentally erase something already recorded on the tape.
® Even when the programming operation has been performed
without any problem, the key may not operate or subsequent
operation may not be possible. This is because some compo-
nents may not accept remote control signals which are slight-
ly different from the original ones.
If this happens, cancel the previously stored signals then per-
form the learning gperation again. (To cancel the stored sig-
nal, refer to the section '‘How to cancel programmed signals’)
® For operations which require pressing two keys together, you
must store both functions in the same key by pressing both
function keys together on the other remote control unit.
@ When batteries in the other remote control unit are exhaust-
ed, signals may not be stored properly.
SSS
29
NLAZO8-X¥Y