JVC RX-807VTN

L£L-L (E€EO? ON)
i
™ Simplifying storage operation
30
Functions of this remote control unit (preset or newly programmed)
can be stored in the desired order with the SEQUENTIAL PROGRAM
KEY {A, B, and C) for individual operations, preferably for frequently
used operations. The simplified operation can be performed by press-
ing the SEQUENTIAL PROGRAM keys.
1. Press the LEARN key.
2. Press the selected SEQUENTIAL PROGRAM key {A, B, C)
Blinks
a OFF
—_ eooLmaece a
\ SEND/LEARN ERROR
®@ If the ERROR indicator lights when the SEND/LEARN indica-
tor is blinking, it means that an operation procedure already
been programmed in that key. If you proceed, a new proce-
dure appended to the procedure programmed in the key. To
program a new procedure in the key, cancel the
preprogrammed procedure first.
Refer to the section ‘‘How to cancel programmed signals.’
@ if only the ERROR indicator lights, incorrect operatin is
assumed.
3. store operations one by one
<For example: Program the operation for turning on the power to
the receiver to play a CD>
@ Press the POWER (AUDIO) key while the SEND/LEARN indi-
cator is blinking
®@ If the SEND/LEARN indicator stops blinking before you press
the key, start again from step 2.
Press the key.
POWER
AUDIO
[we ] OFF OFF
=o [—— } (Reading)
SEND/LEARN ERROR
Lights Lights
Ny t S17
-co-— —-co-— Processing)
Lights
‘ <17 OFF
Keep
pressing.
-co-
f
some
|
(Processing
normally}
If the ERROR indicator blinks, it means that
further programming is inhibited. If you want
to program a new signal in a key, cancel the
signal preprogrammed in that key before retrying
the programming operation.
OFF OFF
oo 3 (Completed)
Lights
viv
eco SJeoe — OE
Release the key
4. Press the CD key of the Source Select keys while the SEND/
LEARN indicator is blinking.
Press the key.
co
OFF OFF
aa oo (Reading)
SEND/LEARN ERROR
Lights Lights
Nis ' Ny ;
= -oxAa- (Processing}
Lights |
OFF
Keep
pressing.
false
f_
co
(Processing
normally)
If the ERROR indicator blinks, it means that
further programming is inhibited. If you want
to program a new signal in a key, cancel the
signal preprogrammed in that key before retrying
the programming operation
OFF OFF
im) =a aI (Completed)
QO Blinks Lights
e, Hany { N17
cJ
Release the key oesh—lece =
@ The indicator lights or blinks each time operations are stored.
Pay attention to the indicator for correct processing. Up to
16 steps can be stored for each combination of key and mode.
5. Press the|_® | key while the SEND/LEARN indicator is blinking.
6. Press the LEARN key again to set the remote control unit to USE
mode.
Notes:
© Two keys cannot be pressed together, for example, REC + PLAY
or REC + PAUSE
@ The SEQUENTIAL PROGRAM KEYS (A, B, and C} allow you to
program up to three operation procedures, each consisting of up
to 16 steps. Depending on the type of signal to be programmed,
not all these steps may not be programmed. If the ERROR indica-
tor blinks three times during a programming operation, it means
that further programming is inhibited.
When programming a sequence of operations to control TV, do not
bring an operation of selecting a channel or adjusting volume immedi-
ately after an opration of turning on power. Otherwise, the stored
operations may not be reproduced as programmed.
(This is because some TVs do not immediately become ready to be
controlled when turned on.)
Insert two or three operations not related to TV (e g. Operations to
control VCR} between an operation of turning the TV power on and
an operation of selecting a channel or any other operation to control
TV
31
;
NLAZLO8-XUu