Kaco blueplanet 2502xi User Manual (English)

Other manuals for Kaco blueplanet 2502xi

Questions and Answers:

S
Sandra BarrettAug 13, 2025
What to do if my Kaco blueplanet 2502xi display is blank and the LEDs aren't lighting up?
- L
  Laura Morgan DVMAug 13, 2025
  A blank display and unlit LEDs on your Kaco Inverter can occur for several reasons. The unit may be in night shutdown mode, which happens when the solar generator voltage is below the minimum grid-feed voltage for an extended period. You can try to view the measured values by switching on the inverter via the night start-up key. Alternatively, there may be no AC line voltage, in which case you should wait until the public utility grid is available again. Low solar generator voltage or the DC/AC switch being OFF can also cause this issue. Check that the DC/AC switch is in the ON (1) position. If the display remains off during daylight hours, contact your solar installer.
J
Jesus BaileyAug 17, 2025
Why is my Kaco blueplanet 2502xi Inverter active but not feeding into the grid?
- N
  Nicholas MontgomeryAug 17, 2025
  If your Kaco Inverter is active but not feeding into the grid, it could be due to insufficient generator voltage, which can happen after sunrise, at sunset, during bad weather, or if solar modules are covered. It could also be that the line voltage or the solar generator voltage is not stable. The inverter checks the line parameters before grid-feed begins, and this switch-on time can take several minutes, varying by country standards.
R
Robert RussellAug 21, 2025
What to do if my Kaco Inverter stops supplying power to the grid shortly after being switched on?
- B
  Brian ThompsonAug 21, 2025
  If your Kaco Inverter feeds into the grid for only a few seconds before switching off again, even with sufficient sunlight, it may be due to a faulty grid separation relay in the inverter.
W
wanda97Aug 25, 2025
Why does the line fuse trip when using my Kaco Inverter?
- J
  john82Aug 26, 2025
  The line fuse may trip because its capacity is too low. The inverter’s pre-fuse capacity should be somewhat higher than the maximum grid-feed current.
S
Sarah KellerAug 29, 2025
Why are the daily energy yields of my Kaco blueplanet 2502xi Inverter different from the energy supply company’s grid-feed counter?
- K
  Kim YoungAug 29, 2025
  The daily yields displayed on your Kaco Inverter may deviate from the values on your supply grid operator’s grid-feed counter by up to 15%, especially if operating at very low power for extended periods of time, due to tolerances of the measuring elements in the inverter.
E
Elizabeth CarpenterSep 1, 2025
How to fix an impossible daily peak value on my Kaco blueplanet 2502xi Inverter?
- C
  Carol SotoSep 1, 2025
  If your Kaco Inverter displays an impossible daily peak value due to faults in the line voltage, note that the inverter will continue to operate normally without yield losses. The value is reset overnight. To immediately reset the value, switch the inverter off and on again using the DC/AC switch in the connection box.
R
rebecca99Sep 5, 2025
Why doesn't my Kaco blueplanet 2502xi feed in the maximum power into low-voltage grid even with high insolation?
- P
  phillipsdavidSep 5, 2025
  If your Kaco Inverter doesn't feed in the maximum power into low-voltage grid despite high insolation, it could be too hot, causing the power to be reduced. Provide sufficient cooling for the unit.
L
Lacey VargasSep 9, 2025
Is noise emission from my Kaco Inverter normal?
- S
  Sara PaceSep 9, 2025
  Noise emissions from the Kaco Inverter can occur due to particular ambient conditions. These emissions do not affect the operation of the inverter.

Kaco blueplanet 2502xi Specifications

General

Max. apparent AC power	2500 VA
Max. input voltage	500 V
Maximum DC Voltage	500 V
Number of MPP Trackers	1
Cooling	Natural convection
Protection Degree	IP54
Rated Output Power	2500 W
AC Nominal Power	2500 W
AC Frequency Range	50 Hz / 60 Hz
Operating Temperature Range	-20°C to +60°C