Kärcher BD 70 W Classic Bp User Manual (English)

Other manuals for Kärcher BD 70 W Classic Bp

Questions and Answers:

R
rchenAug 3, 2025
Why is the suction performance too low on my Kärcher BD 70 W Classic Bp?
- C
  Cathy GarciaAug 3, 2025
  If the suction performance of your Kärcher Scrubber is too low, try these steps: First, shut down the device and drain the waste water. Clean the seals between the waste water tank and the cover, and replace them if they're leaking. Ensure the suction hose is correctly connected to the waste water tank. Check the fluff filter for dirt and clean it if needed. Clean or replace the suction lips at the suction bar. Make sure the cap on the waste water drain hose is closed. Check the suction bar's adjustment. Inspect the suction hose for blockages and leaks, cleaning or replacing it as necessary, ensuring the white marking aligns with the retaining clip when re-inserting the hose.
S
Stephanie WatsonAug 6, 2025
How to start my Kärcher BD 70 W Classic Bp?
- K
  Kevin RodriguezAug 7, 2025
  If your Kärcher Scrubber isn't starting, here's what to do: First, turn the key-operated switch to "1". Then, unlock the emergency stop button on the control panel by turning it (note that not all models have this button). Actuate the safety switch. Insert the battery plug. Check the battery and charge it if necessary. Finally, make sure the battery terminals are correctly connected.
A
Anthony ReyesAug 11, 2025
What to do if the water volume is insufficient in my Kärcher BD 70 W Classic Bp Scrubber?
- D
  Diane LloydAug 11, 2025
  If the water volume is insufficient in your Kärcher Scrubber, take these steps: Begin by checking the fresh water filling level and refill the tank if needed. Increase the water volume using the water volume regulating knob. If you have a BR variant, pull off the water distribution strip on the cleaning head and clean the water channel. Clean the fresh water filter. Lastly, check the hoses for any clogging and clean them if necessary.
Q
qclarkAug 15, 2025
Why are the cleaning results unsatisfactory with my Kärcher BD 70 W Classic Bp Scrubber?
- T
  Thomas PrattAug 15, 2025
  If the cleaning results of your Kärcher Scrubber are unsatisfactory, try the following: Reduce your driving speed. Check the brushes for wear and replace them if needed. Also, ensure that you are using a suitable brush type and detergent for the task.
J
James RodriguezAug 20, 2025
What to do if the suction turbine runs at an increased speed in my Kärcher BD 70 W Classic Bp Scrubber?
- L
  Linda SantiagoAug 20, 2025
  If the suction turbine in your Kärcher Scrubber runs at an increased speed, follow these steps: First, drain the waste water. Then, clean the float. Check the fluff filter and clean it if necessary. Inspect the suction hose for any clogs and remove them. Finally, check the suction bar for clogging and remove any obstructions.
S
Susan EspinozaAug 25, 2025
What to do if the brushes do not rotate on my Kärcher BD 70 W Classic Bp Scrubber?
- J
  Jeremiah HarveyAug 25, 2025
  If the brushes on your Kärcher Scrubber aren't rotating, check to see if they're blocked by any foreign objects and remove them if necessary.
G
Gary Campbell IIAug 28, 2025
Why does my Kärcher BD 70 W Classic Bp Scrubber vibrate during cleaning?
- T
  taylorjasmineAug 28, 2025
  If your Kärcher Scrubber vibrates during cleaning, try using a softer brush.

Kärcher BD 70 W Classic Bp Specifications

General

Working width, brush	700 mm
Battery voltage	24 V
Brush speed	180 rpm
Battery running time	4 h
Voltage	24 V
Tank fresh/dirty water	85/85 l
Brush contact pressure	40 g/cm²
Frequency	50 Hz