What to do if my KaVo Medical Equipment has stopped working?
If your KaVo Medical Equipment has completely stopped working, there are several potential causes: * The main switch might be off, so switch it on. * The emergency laser stop could be activated; release it. * The power line may not be connected; ensure it is properly connected.
Why does the touchscreen display go out during operation on my KaVo Medical Equipment?
If the touchscreen display on your KaVo KEY Laser 1243 Medical Equipment goes out during operation, it is likely due to a safety-relevant fault that caused the unit to switch off automatically. Try switching the KEY Laser 1243 off and on again. If no message appears on the touchscreen, contact the service.
Why is the spray at the handpiece poor on my KaVo Medical Equipment?
If you're experiencing poor spray at the handpiece of your KaVo Medical Equipment, it could be due to a furred or soiled spray nozzle. Try piercing the spray nozzle with a jet needle, which is included among the accessories. Alternatively, try cleaning the spray nozzle.
What to do if there is no spray at the handpiece of my KaVo Medical Equipment?
If there is no spray at the handpiece of your KaVo Medical Equipment, there are a few possible reasons: * The spray reservoir might be empty, so fill it with spray water. * The spray regulation screw on the laser coupling could be closed; open it. * The spray nozzle might be blocked; clean it.
Why am I getting an unsatisfactory laser result from my KaVo Medical Equipment?
If you are getting unsatisfactory laser results with your KaVo Medical Equipment, it might be because the exit window on the handpiece is soiled. Clean the exit window. Alternatively, the exit window on the handpiece might be faulty, in which case you should replace it.
What to do if there is a leak in the handpiece of my KaVo Medical Equipment?
If you notice a leak in the handpiece of your KaVo Medical Equipment, it could be due to faulty O-rings on the laser tube coupling. Replace the O-ring. If the leak is in the laser instrument, it is necessary to have the optical system checked by a Service Technician or the instrument sent to KaVo for checking.
Why the KaVo KEY Laser III 1243 laser cannot switch to ready mode?
If the KaVo dental laser cannot switch to ready mode, first, ensure the handpiece is correctly positioned in the swing arm to actuate the holder switch. Next, check that the entrance doors to the treatment room are closed. Finally, verify that the jumper for the door contact connection is correctly inserted and tightened if door switches are not installed.
What to do if KaVo Dental equipment handpiece does not emit any spray?
If the handpiece of your KaVo Dental equipment does not emit any spray, you should first check if the spray reservoir is empty and fill it if needed. Then, verify that the spray regulating screw in the laser coupling is open. Finally, inspect the spray nozzle for clogs and clean it if necessary.
Why does the touchscreen display disappear during operation of KaVo KEY Laser III 1243 Dental equipment?
If the touchscreen display of your KaVo Dental equipment disappears during operation, it is because the device independently turns off when malfunctions arise that affect safety. Turn the KEY Laser 3+ / III upgraded off and on. If the display does not appear on the touchscreen, call service.
Why is the handpiece of my KaVo Dental equipment leaking?
If the handpiece of your KaVo Dental equipment is leaking, it could be due to defective O-rings on the laser hose coupling, in which case you should replace the O-rings. Alternatively, there might be a leaky laser instrument, which requires a technician to check the optical system, or you can send the instrument to KaVo to be checked.
General| Brand | KaVo |
|---|---|
| Model | KEY Laser III 1243 |
| Category | Dental equipment |
| Language | English |
Defines the intended use and proper application of the KEY Laser 1243 dental device.
Outlines crucial guidelines for safe and correct operation, maintenance, and installation.
Details hazard levels, warning symbols, and general safety protocols for device operation.
Covers specific safety regulations, legal provisions, and requirements for laser operation.
Provides general safety instructions, handling precautions, and warnings related to the device's operation.
Provides a guide to common malfunctions, their causes, and recommended remedies for self-help.
To Next Page
