What does it mean if SAFEdrive icon flashes yellow on KaVo Medical Equipment?
If the SAFEdrive icon flashes yellow on your KaVo Medical Equipment, it means the motor is overloaded. If using a third-party handpiece, deactivate SAFEdrive or use a KaVo high-speed handpiece. If using a KaVo handpiece, relieve the load for at least 2 seconds. Once the motor reaches maximum speed and the icon turns yellow, continue working in intermittent mode.
What does Event E14 mean on KaVo Medical Equipment?
Event E14 on your KaVo Medical Equipment indicates a motor overload. Relieve the motor of its load, then stop and start it using the foot control.
What does Event E8 mean on KaVo Medical Equipment?
Event E8 on your KaVo Medical Equipment means that saved data or settings have been reset to the starting value. Confirm the message and check or correct the program settings.
What does Event E5 mean on KaVo Medical Equipment?
Event E5 on your KaVo Medical Equipment indicates automatic light and motor shut-off during continuous operation of the motor. Comply with the defined operating mode.
What to do if KaVo Medical Equipment malfunctions (no display, LED on the rear does not flash)?
If your KaVo Medical Equipment malfunctions with no display and the LED on the rear doesn't flash, the issue is likely a lack of voltage supply. Check and restore the voltage supply and ensure the connection is correct. Verify that the standby LED on the power supply is on; if not, replace the power supply. If the problem persists, contact a service engineer.
What to do for all other events on KaVo Medical Equipment?
For all other events on your KaVo Medical Equipment, it indicates an internal system error. Turn the unit off and on.
What does Event E3 mean on my KaVo ELECTROmatic M Dental equipment?
Event E3 indicates that no motor is attached. Connect the motor.
What does Event E2 mean on my KaVo Dental equipment?
Event E2 indicates that the foot control is being actuated during start-up. Make sure you do not press the foot control when you switch the unit on.
What to do if my KaVo ELECTROmatic M Dental equipment malfunctions (no display, the LED on the rear of the device flashes)?
If your device malfunctions with no display but the LED on the rear flashes, it could be due to no voltage supply on the control panel or no connection to the control panel. Check and restore the correct connection. Try replacing the connection cord to the control panel or replacing the control panel itself. If error persists, notify the service engineer.
Why is there no or insufficient spray water in my KaVo Dental equipment?
There could be several reasons for insufficient spray water. The spray water regulation might be closed, so open it as much as possible. The water line could be soiled; in this case, pull off the handpiece and actuate the spray water in bursts to rinse it. Another cause may be that the filter insert is soiled, so replace the filter on the water inlet. Finally, the spray water on the treatment center or foot control could be closed, so open the spray on the treatment center. If the error persists, unscrew the turbine hose and check if any water flows. If no water flows, notify a service engineer.
Read instructions before first startup to avoid misuse and prevent damage.
Measures to prevent infection risks from contaminated medical devices.
Precautions regarding the use of the product in areas with explosion risks.
Ensuring product's technical condition and performing user checks before operation.
Preventing liquid ingress to avoid electric shock and injury.
Guidelines for using approved accessories and combining with other equipment safely.
User training and qualification requirements for operating the device.
Defines the purpose and application of the ELECTROmatic in dental treatments.
Procedure for calibrating the foot control for optimal operation.
Instructions on how to adjust various device settings like speed, LUX, and key tones.
Steps to start the motor and reach the set maximum speed.
Instructions on how to adjust the amount of spray water for cooling.
How to change and save speed settings using the control panel or foot control.
Explanation of SAFEdrive for preventing overheating and burn injuries.
Instructions on how to enable or disable the SAFEdrive function.
Guidance on using SAFEdrive and handling alerts or errors.
Procedures for cleaning the unit, including preparation and manual methods.
Guidelines and recommended products for disinfecting the unit and spray water.
Troubleshooting steps for issues with spray water delivery or regulation.
Diagnosing issues when the device display is off or LED is not flashing.
Troubleshooting device issues when the control panel LED flashes.
Resolving problems where the maximum motor speed is not achieved.
Troubleshooting steps for a sluggish motor or handpiece performance.
Resolving problems with the LUX light being red or not turning on.
Actions to take when the SAFEdrive icon flashes yellow, indicating motor overload.
Troubleshooting SAFEdrive error status where the motor stops automatically.
Interpreting and resolving specific event error codes displayed by the unit.
Steps to resolve general internal system errors.
General| Motor Type | Brushless |
|---|---|
| Torque | 3.5 Ncm |
| Autoclavable | Yes |
| Type | Electric motor |
| Speed | Up to 40, 000 rpm |
| Control | Control unit with display |
| Connection | ISO 3964 |
| Material | Stainless steel |
| Compatibility | Compatible with most dental units with electric motor connection |
To Next Page