What to do for all other events on KaVo ELECTROmatic TM?
If you encounter any other events on your KaVo dental equipment, it indicates an internal system error. Turn the unit off and then on again. If the error persists, contact a service engineer.
What to do if SAFEdrive icon flashes yellow on KaVo Dental equipment?
If the SAFEdrive icon flashes yellow, indicating the motor is overloaded, especially if you're using a third-party handpiece, deactivate SAFEdrive or use a KaVo high-speed handpiece. If using a KaVo high-speed handpiece, relieve the load on the handpiece for at least 2 seconds by lifting it off the tooth. Once the motor reaches maximum speed and the icon turns yellow, continue working in intermittent mode.
Why is there no or insufficient spray water in my KaVo ELECTROmatic TM Dental equipment?
There could be several reasons for insufficient spray water: - The spray water regulation might be closed; in this case, open the spray water fully. - The water line may be soiled; to resolve this, pull off the handpiece and actuate the spray water in bursts to rinse it. - The filter insert could be soiled; if so, replace the filter on the water inlet. - The spray water on the treatment unit or foot control might be closed; open the spray on the treatment unit. If the problem continues, unscrew the turbine hose to check for water flow. If there's no flow, contact a service engineer.
What to do if my KaVo ELECTROmatic TM Dental equipment malfunctions with no display and the LED on the rear of the device does not flash?
If your device malfunctions with no display and the LED on the rear doesn't flash, it may be due to no voltage supply. Check and restore the voltage supply and ensure the connection is correct. Check that the standby LED on the power supply is on. If it's not on, replace the power supply. If the problem persists, contact a service engineer.
What to do if my KaVo ELECTROmatic TM malfunctions with no display and the LED on the rear of the device flashes?
If your device malfunctions (no display, the LED on the rear of the device flashes), this may indicate no voltage supply to the control panel. Check and restore the correct connection. If this doesn't resolve the issue, try replacing the connection cable to the control panel, or replacing the control panel itself. If the problem continues, notify a service engineer.
What to do if KaVo ELECTROmatic TM Dental equipment device malfunctions (no display, the LED on the rear of the device flashes)?
If your KaVo dental equipment malfunctions with no display but the LED on the rear flashes, it suggests there's no voltage supply to the control panel or no connection to it. Check and restore the correct connection. If that doesn't work, replace the connection cord to the control panel or replace the control panel itself. If problems continue, contact a service engineer.
What to do if KaVo ELECTROmatic TM device malfunctions (no display, the LED on the rear of the device does not flash)?
If your KaVo dental equipment malfunctions with no display and the LED on the rear doesn't flash, the cause might be no voltage supply. Check and restore the correct voltage supply and connection. Ensure the standby LED on the power supply is lit. If it's not, replace the power supply. If the issue continues, contact a service engineer.
Why maximum speed is not reached on KaVo Dental equipment?
If your KaVo dental equipment isn't reaching maximum speed, it could be due to a few reasons. The supply pressure might have dropped significantly; try repeatedly pushing the foot control down fully to allow the motor to start up and calibrate automatically, increasing the speed. Alternatively, there might be a kink or leak in the supply hose; remove any kinks and inspect for damage, replacing the hose if necessary. Lastly, the motor or handpiece could be sluggish, in which case you should replace or repair the handpiece. If the issue persists, contact a service engineer.
What does Event E9, E46 mean on KaVo Dental equipment?
Event E9 or E46 indicates that communication between the motor control and panel is interrupted. This may occur when you reset to factory settings and should reset automatically. If the error persists, switch the device off and on again. If the error persists, notify the service engineer.
What does Event E5 mean on KaVo ELECTROmatic TM?
Event E5 indicates an automatic light and motor shut-off during continuous operation of the motor. Ensure you comply with the defined operating mode.
Provides essential guidance for safe and correct operation of the device.
Identifies intended users and outlines service procedures and contact details.
Details warranty terms, procedures for handling transport damage, and disposal guidelines.
Covers infection, explosion, electrical hazards, and ingress of liquids.
Specifies user qualifications, service requirements, and safe handling practices.
Addresses potential interference with medical systems and necessary precautions.
Defines the device's purpose, proper use, and available configurations.
Lists included components and accessories for different ELECTROmatic models.
Explains the touch display, modes, and operating controls.
Provides detailed technical data, including dimensions, power, and environmental requirements.
Guides on selecting the installation site and available mounting options.
Details steps for preparing the device, connecting components, and checking installation.
Outlines necessary conditions for compressed air, water, and electrical connections.
Covers connecting the motor, hoses, and calibrating the foot control.
Explains how to adjust parameters like brightness, volume, and file settings.
Covers powering the unit on/off and understanding the display.
Details speed settings, transmission ratios, and SAFEdrive function in PREP mode.
Explains ENDO mode operation, file database, and sequence customization.
Provides steps for safely disconnecting the device and its components.
Details manual cleaning, disinfection, and germ reduction steps.
Covers proper storage and essential checks after reprocessing.
Step-by-step guide for replacing the water filter insert.
Instructions for replacing LED lamps in motors and bases.
Procedure for replacing a defective motor hose.
Lists potential issues, causes, and solutions for device operation.
Catalog of compatible accessories and consumable parts with material numbers.
Manufacturer's declaration on electromagnetic emissions per standards.
Information on device immunity and recommended distances for communication equipment.
General| Type | Electric Micromotor System |
|---|---|
| Foot Control | Variable Speed Foot Control |
| Noise Level | Low Noise Operation |
| Speed | Up to 40, 000 RPM |
| Compatibility | KaVo handpieces |
| Handpiece Connection | ISO 3964 |
| Display | Digital display |
| Autoclavable Components | Handpieces and some attachments |
| Supply voltage | 100-240V AC, 50/60Hz |
To Next Page