KB Electronics KBAC-27D - KBAC-217, 217 S, 217 F, 217 SF, 416, 416 S, 416 F, 416 SF Mechanical Specifications

24 pages

To Next Page

To Previous Page

KBAC SERIES INSTALLATION AND OPERATION MANUAL

FIGURE 10

KBAC-217, 217S, 217F, 217SF, 416, 416S, 416F, 416SF MECHANICAL SPECIFICATIONS (Inches / mm)

Main Page

Table of Contents2
Drive Model No., Part No., and Case Reference Size3
Quick-Start Instructions4
- Mounting Instructions4
- AC Line Input Fusing4
- AC Line Input Connection4
- Motor Connection4
- Ground Connection4
- 60 Hz and 50 Hz Motor Operation4
- Start/Stop Switch4
- Jumper Settings4
- Trimpot Adjustments4
Maximum Allowed Motor Torque Vs. Speed5
Open Ventilated Motor with External Fan Cooling5
Safety Warnings5
Important Application Information5
- Motor with External Fan Cooling5
- Electronic Motor Overload Protection5
Introduction6
- Standard Features6
- Performance Features6
- Protection Features6
Electrical Ratings7
General Performance Specifications7
KBAC-24D Drive Layout8
KBAC-27D Drive Layout9
KBAC-29, 29 (1P), 45, 48 Drive Layout10
KBAC-217, 217S, 217F, 217SF, 416, 416S, 416F, 416SF Drive Layout11
KBAC-24D Mechanical Specifications12
Mounting12
KBAC-27D, 29, 29 (1P), 45, 48 Mechanical Specifications13
KBAC-217, 217S, 217F, 217SF, 416, 416S, 416F, 416SF Mechanical Specifications14
KBAC-24D, 27D, 29 (1P) AC Line Input, Motor, and Ground Connections15
- Motor Connection16
- Ground Connection16
- Remote Main Speed Potentiometer Connection16
AC Line Input Fusing15
Electrical Connections15
- AC Line Input Connection15
Terminal Block Wire Size and Tightening Torque Specifications15
KBAC-29, 45, 48 AC Line Input, Motor, and Ground Connections16
KBAC-217, 217S, 217F, 217SF, 416, 416S, 416F, 416SF AC Line Input, Motor, and Ground Connections16
- Remote Start/Stop Switch Connections17
- Automatic Restart17
- Voltage Following Connections17
- Enable Circuit Connection17
Remote Start/Stop Switch Connection with Normally Open Stop Contact17
Remote Start/Stop Switch Connection with Normally Closed Stop Contact17
Start/Stop Function Eliminated17
- Run/Fault Relay Connection18
Run/Fault Relay Output Contacts Connection18
Typical Hi-Pot Test Setup18
Recommended High Voltage Dielectric Withstand Testing (Hi-Pot Testing)18
Reconditioning the Bus Capacitors18
Drive Operating Condition and Run/Fault Relay Contact Status18
Available Torque Vs. Output Frequency19
- Boost Mode Selection (J6)20
- Braking Mode Selection (J7)20
- Run/Fault Output Relay Operation Selection (J8)20
- Stop Contact Type Selection (J9)20
- Torque Mode Selection (J10)20
- Jumper J11 (Factory Use Only)20
- Switching Frequency and GFCI Selection (Third Generation (3G) Drives Only) (J12)20
Setting Selectable Jumpers19
- AC Line Input Voltage Selection (KBAC-24D, 27D Only) (J1)19
- Motor Horsepower Selection (J2)19
- Automatic Ride-Through or Manual Start Selection (J3)19
- Motor Frequency Selection (J4 and J5)19
  - Setting the Drive for 50 Hz or 60 Hz Motor Operation (J4 and J5)19
  - Setting the Drive for Two Times the Rated Motor RPM (J4 and J5)19
Drive Operation20
- Start-Up Procedure20
- Restarting the Drive after a Fault Has Cleared21
Minimum Speed Trimpot (MIN) Range21
Maximum Speed Trimpot (MAX) Range21
Acceleration Trimpot (ACCEL) Range21
- Slip Compensation Trimpot (COMP)22
- Motor Overload (I T) with RMS Current Limit Trimpot (CL)22
- Boost Trimpot (BOOST)22
- Jog Trimpot (JOG)22
Trimpot Adjustments21
- Minimum Speed Trimpot (MIN)21
- Maximum Speed Trimpot (MAX)21
- Acceleration Trimpot (ACCEL)21
- Deceleration Trimpot (DECEL)21
- DC Injection Brake Trimpot (DECEL)21
Slip Compensation Trimpot (COMP) Range22
Current Limit Trimpot (CL) Range22
Trip Time Vs. Motor Current22
Boost Trimpot (BOOST) Range22
Jog Trimpot (JOG) Range22
Run-Stop-Jog Switch Connection22
Diagnostic Leds23
- Power on LED (PWR)23
- Status LED (ST)23
Optional Accessories23
Drive Operating Condition and Status LED Indicator23

KB Electronics KBAC-27D - KBAC-217, 217 S, 217 F, 217 SF, 416, 416 S, 416 F, 416 SF Mechanical Specifications

Table of Contents

Related product manuals