To Next PageTo Next PageWhat to do if my Kenmore 796.8219 will not turn on?
If your Kenmore Dryer won't turn on, first ensure the power cord is securely plugged into a grounded outlet that matches the dryer's rating plate. Also, check your house fuse or circuit breaker. Reset the circuit breaker or replace the fuse, but do not increase the fuse capacity. If a circuit overload is the issue, have it corrected by a qualified electrician.
Why is my Kenmore 796.8219 Dryer not heating up?
If your Kenmore dryer isn't heating, check the following: Reset the circuit breaker or replace the fuse, but do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. For gas models, confirm that both the house gas shutoff and the dryer gas shutoff valves are fully open. Verify that other gas appliances in the home are working normally.
How to prevent lint on clothes in my Kenmore 796.8219?
To prevent lint on clothes when using your Kenmore dryer: * Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. * Separate lint producers (like cotton towels) from lint trappers (like linen pants). * Use a fabric softener to reduce static electricity, following the manufacturer’s instructions. * Divide extra-large loads into smaller ones. * Always check pockets thoroughly before washing and drying.
Why is there excess static in clothes after drying in my Kenmore Dryer?
Excess static in clothes after drying in your Kenmore dryer can be due to several reasons. Ensure you are using fabric softener correctly, or utilize the STATIC SHIELD option if your dryer has it. Overdrying can also cause static, so adjust your settings for a shorter drying time or use SENSOR DRY cycles with a 'Less Dry' setting. Synthetic fabrics are more prone to static, so try using fabric softener or shorter drying times for these items.
What to do if clothes are wrinkled after drying in my Kenmore 796.8219 Dryer?
If clothes are wrinkled after drying in your Kenmore dryer, it could be due to overdrying. Try a shorter drying time or a LESS DRY setting, removing items while they still have a slight amount of moisture. Also, use the WRINKLE GUARD option to tumble the clothes briefly every few minutes for up to 150 minutes to help prevent wrinkling.
What to do if there is a partial blockage of the ductwork in my Kenmore 796.8219 Dryer?
If there is a partial blockage of the ductwork due to lint buildup or a foreign object, the ductwork should be checked and cleaned immediately. The dryer can still be used, but drying times will be longer, and energy consumption will increase.
Why are there greasy or dirty spots on clothes after using my Kenmore Dryer?
Greasy or dirty spots on clothes after using your Kenmore dryer can be caused by drying clean and dirty clothes together. Only use your dryer to dry clean items, because dirty items can soil clean clothes placed in the same or subsequent loads. It can also happen if clothes were not properly cleaned or rinsed before placing them in the dryer, so ensure clothes are completely cleaned or rinsed according to the instructions for your washer and detergent. Some difficult soils may require pre-treating prior to washing.
How to fix ductwork that is too long or has too many turns/restrictions for my Kenmore 796.8219 Dryer?
To fix ductwork that is too long or has too many turns/restrictions, install a shorter or straighter duct run. See the Installation Instructions for details.
Why is the drying time not consistent in my Kenmore Dryer?
The drying time for a load will vary depending on the type of heat used (electric, natural, or LP gas), the size of the load, the type of fabrics, the wetness of the clothes, and the condition of the exhaust ducts and lint filter. Even an unbalanced load in the washer can cause poor spinning resulting in wetter clothes which will take longer to dry.
What to do if steam features are not working on my Kenmore 796.8219 Dryer?
If the steam feature isn't working and no error code is displayed, check for condensation inside the door during the steam portion of the cycle, as steam is not directly visible. Ensure the steam feeder is filled with water to the MAX line, properly seated, and the drawer is fully closed. Turn the dryer off, then back on, and restart the steam cycle. Do not use distilled water, as the water level sensors in the steam generator won't work.
General| Brand | Kenmore |
|---|---|
| Model Number | 796.8219 Series |
| Appliance Category | Dryer |
| Energy Efficiency | Energy Star Certified |
| Dryer Heating Source | Electric |
| Number of Options | 5 |
| Wrinkle Guard Option | Yes |
| Steam Feature | Yes |
| Moisture Sensor | Yes |
| Interior Light | Yes |
| Color | White |
| Voltage | 240 V |
| Amperage | 30 A |
| Type | Dryer |
| Control Type | Electronic |
| Width | 27 inches |
| Height | 38 in. |
| Drum Material | Aluminized Alloy |
| Drying Programs | Multiple including Normal, Heavy Duty, Delicates, Quick Dry |
