Kenmore 796.8219 Series

Other manuals for Kenmore 796.8219 Series

Use & Care Guide108 pages

Use & Care Guide And Installation Instructions72 pages

Questions and Answers

C
Carla CaldwellNov 23, 2025
Why do my clothes take so long to dry in my Kenmore 796.8219 Dryer?
- C
  Christopher HodgeNov 24, 2025
  Several factors can cause clothes to take too long to dry in your Kenmore dryer. Check the following: * Ensure the exhaust ductwork is properly configured and free of debris, lint, and obstructions. Make sure the outside wall dampers can open properly. * Separate heavy items from lightweight items. * For large loads of heavy fabrics, separate these items into smaller loads of a consistent size. * Use the appropriate control settings for the type of load you are drying. Some loads may require an adjustment of the dry level for proper drying. * Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. * Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the problem is a circuit ...
R
Robert WellsAug 23, 2025
Why is my Kenmore 796.8219 Dryer not heating up?
- E
  Emily NovakAug 23, 2025
  If your Kenmore dryer isn't heating, check the following: Reset the circuit breaker or replace the fuse, but do not increase fuse capacity. If the problem is a circuit overload, have it corrected by a qualified electrician. For gas models, confirm that both the house gas shutoff and the dryer gas shutoff valves are fully open. Verify that other gas appliances in the home are working normally.
G
Garrett FrenchAug 26, 2025
How to prevent lint on clothes in my Kenmore 796.8219?
- V
  victorianormanAug 26, 2025
  To prevent lint on clothes when using your Kenmore dryer: * Remove the lint from the filter before every load. With the lint removed, hold the filter up to a light to see if it is dirty or clogged. * Separate lint producers (like cotton towels) from lint trappers (like linen pants). * Use a fabric softener to reduce static electricity, following the manufacturer’s instructions. * Divide extra-large loads into smaller ones. * Always check pockets thoroughly before washing and drying.
K
Kenneth SteinAug 27, 2025
Why is there excess static in clothes after drying in my Kenmore Dryer?
- S
  Steve McdonaldAug 27, 2025
  Excess static in clothes after drying in your Kenmore dryer can be due to several reasons. Ensure you are using fabric softener correctly, or utilize the STATIC SHIELD option if your dryer has it. Overdrying can also cause static, so adjust your settings for a shorter drying time or use SENSOR DRY cycles with a 'Less Dry' setting. Synthetic fabrics are more prone to static, so try using fabric softener or shorter drying times for these items.
A
Anna CarterAug 28, 2025
What to do if clothes are wrinkled after drying in my Kenmore 796.8219 Dryer?
- D
  Denise FloresAug 29, 2025
  If clothes are wrinkled after drying in your Kenmore dryer, it could be due to overdrying. Try a shorter drying time or a LESS DRY setting, removing items while they still have a slight amount of moisture. Also, use the WRINKLE GUARD option to tumble the clothes briefly every few minutes for up to 150 minutes to help prevent wrinkling.
W
Wesley JonesSep 18, 2025
Why can't I see steam vapor at the beginning of the cycle in my Kenmore 796.8219 Dryer?
- D
  Derrick GreeneSep 18, 2025
  It is normal if you can't see steam vapor at the beginning of the Kenmore Dryer's steam cycle. Steam is released at different stages depending on the option selected. Typically, steam won't be visible, though condensation might appear on the inside of the door.
C
Charles RogersSep 14, 2025
Why does water drip from the nozzle when the Steam Cycle starts on my Kenmore 796.8219 Dryer?
- J
  Joshua WardSep 15, 2025
  It is normal for water to drip from the nozzle when the Steam Cycle starts on your Kenmore Dryer. This is simply steam condensation, and the dripping should stop shortly.
J
jbrownSep 16, 2025
Why doesn't the drum turn during the Steam Cycle on my Kenmore 796.8219?
- R
  Russell WardSep 16, 2025
  It is normal for the drum not to turn continuously during the Steam Cycle of your Kenmore Dryer. The drum turns off and only tumbles intermittently to ensure the steam vapor remains in the drum.
E
eric34Sep 7, 2025
What to do if my Kenmore 796.8219 shows error E3?
- F
  fjacksonSep 7, 2025
  If your Kenmore Dryer displays the error code E3, it indicates that the water level in the steam feeder might be too low. To resolve this, fill the feeder with water and restart the cycle.
L
Linda StoneSep 4, 2025
What to do if steam features are not working on my Kenmore 796.8219 Dryer?
- J
  Jeffery AndersonSep 4, 2025
  If the steam feature isn't working and no error code is displayed, check for condensation inside the door during the steam portion of the cycle, as steam is not directly visible. Ensure the steam feeder is filled with water to the MAX line, properly seated, and the drawer is fully closed. Turn the dryer off, then back on, and restart the steam cycle. Do not use distilled water, as the water level sensors in the steam generator won't work.

Summary

Safety and Precautions

General Safety & Gas Leak Procedures

Covers general safety, grounding, and steps to take if gas is smelled.

ESD Handling for Electronics

Guidelines for handling sensitive electronics to prevent ESD damage.

Installation Instructions

Power Cord Connection

Gas Supply Pipe Connection

Component Testing Procedures

Thermal Components and Lamp Testing

Testing procedures for thermal cut-offs, thermostats, and lamp holder.

Electrical Components Testing (Heater, Thermistor, Gas Valve, Igniter)

Resistance checks for heater, thermistor, gas valve, and igniter.

Gas Type Specific Components Testing

Testing procedures for gas type hi-limit thermostats and thermal cut-offs.

Motor Diagram and Schematic

Wiring Diagram

Steam Functionality

Steam Dryer Troubleshooting and Error Codes

Diagnostic Test Mode

Electrical Supply Test

Thermistor Test

Tab Relay Connections

Incorrect Tab Relay Wiring

Motor Test

Moisture Sensor Test

Door Switch Test

Heater Switch Test (Electric)

Gas Valve Test

Gas System Configuration

Gas Setting Conversion (Natural;Propane)

Top Plate Disassembly

Panel Drawer & Control Panel Disassembly

Cabinet Cover Disassembly

Drum Assembly & Related Components Disassembly

Filter, Blower Housing, and Back Cover Disassembly

Exploded Views

Drum & Motor Assembly Exploded View (Gas Type)

Kenmore 796.8219 Series Specifications

General

Brand	Kenmore
Model Number	796.8219 Series
Appliance Category	Dryer
Energy Efficiency	Energy Star Certified
Dryer Heating Source	Electric
Number of Options	5
Wrinkle Guard Option	Yes
Steam Feature	Yes
Moisture Sensor	Yes
Interior Light	Yes
Color	White
Voltage	240 V
Amperage	30 A
Type	Dryer
Control Type	Electronic
Width	27 inches
Height	38 in.
Drum Material	Aluminized Alloy
Drying Programs	Multiple including Normal, Heavy Duty, Delicates, Quick Dry