Need help?Do you have a question about the Kenwood KAC-728 and is the answer not in the manual?
Power Output| max power output (4 Ω) | 200 W × 2 |
|---|---|
| bridge power output | 600 W × 1 |
| rated power output (4 Ω) | 100 W × 2 |
| rated power output (2 Ω) | 150 W × 2 |
Audio Specifications| frequency response | 5 Hz ~ 50 kHz |
|---|---|
| signal to noise ratio | 100 dB |
| sensitivity (max) | 0.2 V |
| sensitivity (min) | 5.0 V |
| input impedance | 10 kΩ |
| low pass filter | 80 Hz |
General Specifications| operating voltage | 14.4 V |
|---|---|
| current consumption | 28 A |
| dimensions | 220 × 56.1 × 300 mm |
| weight | 3.6 kg |
Power Output| max power output (4 Ω) | 100 W × 2 |
|---|---|
| bridge power output | 300 W × 1 |
| rated power output (4 Ω) | 50 W × 2 |
| rated power output (2 Ω) | 75 W × 2 |
Audio Specifications| frequency response | 10 Hz ~ 45 kHz |
|---|---|
| signal to noise ratio | 100 dB |
| sensitivity (max) | 0.15 V |
| sensitivity (min) | 4.0 V |
| input impedance | 10 kΩ |
| low pass filter | 80 Hz |
General Specifications| operating voltage | 14.4 V |
|---|---|
| current consumption | 19 A |
| dimensions | 220 × 56.1 × 228 mm |
| weight | 2.7 kg |
Power Output| max power output (4 Ω) | 70 W × 2 |
|---|---|
| bridge power output | 200 W × 1 |
| rated power output (4 Ω) | 35 W × 2 |
| rated power output (2 Ω) | 50 W × 2 |
Audio Specifications| frequency response | 5 Hz ~ 50 kHz |
|---|---|
| signal to noise ratio | 100 dB |
| sensitivity (max) | 0.2 V |
| sensitivity (min) | 5.0 V |
| input impedance | 10 kΩ |
| low pass filter | 80 Hz |
General Specifications| operating voltage | 14.4 V |
|---|---|
| current consumption | 16 A |
| dimensions | 220 × 55 × 160 mm |
| weight | 1.8 kg |
Key precautions to prevent injury, fire, and unit damage.
Guidance on cleaning the unit and a list of included accessories.
Explains the power indicator and its role in protection.
Lists scenarios that activate the protection circuit.
Detailed sequence for installing the power amplifier.
Critical safety notes during the installation process.
Adjusts audio filtering (HPF/LPF) and amplification modes (Stereo/Mono).
Manages audio signal input and sensitivity levels.
Interfaces for power, speakers, RCA, and remote connections.
Steps and diagrams for connecting via RCA cables.
Instructions for connecting using speaker level inputs.
Important safety warnings applicable to all connection types.
Guides for stereo and bridged speaker wiring configurations.
Recommendations for speaker impedance and power ratings.
Illustrates and explains the power cable connection process.
Essential wiring advice to prevent noise and ensure safety.
Specifies fuses and wire cross-sections for each amplifier model.
Advice on selecting installation location and using extension cables.
Critical warnings about installation risks and vehicle safety.
Demonstrates various speaker and subwoofer connection configurations.
Explains tri-mode setup, frequency division principles, and safety.
Solutions for when no sound or sound from only one side is present.
Troubleshooting steps for incorrect audio output levels.
Guidance for resolving issues with distorted sound quality.
Technical data on power output, frequency response, and input impedance.
Specs on operating voltage, current draw, dimensions, and weight.
To Next Page
