What to do if my Kenwood Car Receiver sound cannot be heard?
If you cannot hear any sound from your Kenwood Car Receiver, try these solutions: First, adjust the volume to make sure it's at an audible level. Next, inspect the cords and connections to ensure they are properly connected. Finally, clean the connectors to remove any dirt or debris that might be interfering with the sound.
What to do if Bluetooth pairing cannot be made on Kenwood Car Receiver?
If you're having trouble pairing a Bluetooth device with your Kenwood Car Receiver: * Ensure you've entered the same PIN code on both devices. * Try deleting the pairing information from both the receiver and the Bluetooth device, and then attempt the pairing process again.
What to do if setting/deleting the remote control ID is unsuccessful on Kenwood Car Receiver?
If setting or deleting the remote control ID is unsuccessful and you see “SET ERROR” or “DEL ERROR” on your Kenwood Car Receiver, turn the power off, then turn it back on, and try the operation again.
Why does my Kenwood Car Receiver say 'MISWIRING CHECK WIRING THEN PWR ON'?
If your Kenwood Car Receiver displays the message “MISWIRING CHECK WIRING THEN PWR ON”, turn the power off. Then, check to ensure the terminals of the speaker wires are properly insulated. Turn the power back on.
What does “CHECK ANTENNA” mean on my Kenwood Car Receiver and how to fix it?
If your Kenwood Car Receiver displays “CHECK ANTENNA”, it means you should check that the antenna and its connection are in good condition.
What to do if my Kenwood Car Receiver disc cannot be ejected?
If the disc cannot be ejected from your Kenwood Car Receiver, press and hold the M button to forcibly eject the disc, being careful not to drop it. If this does not solve the problem, reset the unit.
Why does my Kenwood Car Receiver say “NO SIGNAL”?
If your Kenwood Car Receiver displays “NO SIGNAL”, make sure the antenna is mounted outside the vehicle.
What does “NO MUSIC” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “NO MUSIC”, connect a USB device that contains playable audio files.
How to fix echo or noise during a phone conversation on my Kenwood Car Receiver?
If you experience echo or noise during phone conversations using your Kenwood Car Receiver, try the following: 1. Adjust the microphone unit’s position. 2. Check the [ECHO CANCEL] setting.
What does “USB HUB IS NOT SUPPORTED” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “USB HUB IS NOT SUPPORTED”, it means that the unit cannot support a USB device connected via a USB hub.
Device operation cautions and FCC compliance statements.
Highlights essential pre-use checks, warnings, and cautions for safe operation.
Guides users through selecting display language and disabling the demonstration mode.
Step-by-step instructions for setting the unit's clock and date.
Covers initial setup for features like audio control and source selection.
Covers starting playback for various media sources like CD, USB, iPod, and Android devices.
Details controls for playback, track selection, folder navigation, repeat, and random play.
Manages control modes for iPod/Android and selects the music drive for USB playback.
Explains how to select files from folders or lists for iPod/Android devices.
Covers connecting the SiriusXM tuner, activation, and starting satellite radio listening.
Manages favorite channels and enables playback from the beginning of songs.
Guides initial pairing of Bluetooth devices like phones and audio players.
Covers answering, rejecting, and handling incoming calls via Bluetooth.
Explains how to make calls via history, phonebook, or number dialing.
Accesses phonebook contacts and initiates voice commands for calling.
Connects and controls audio playback from Bluetooth-enabled devices.
Adjusts subwoofer level, manual equalizer settings, and preset EQs.
Customizes bass boost, loudness, and subwoofer output levels.
Configures speaker sizes and crossover frequencies for optimal sound.
Adjusts rear speaker HPF and subwoofer LPF settings.
Optimizes sound staging by adjusting speaker delay and distance.
Provides guidance on measuring speaker distances for accurate DTA setup.
Addresses issues like no sound, wiring checks, and poor radio reception.
Resolves problems related to disc errors, file playback, and device recognition.
Continues troubleshooting for CD/USB/iPod issues like character display and device errors.
Solves problems related to Android device playback and Pandora app functionality.
Addresses issues with SiriusXM channels and Bluetooth connectivity.
Covers Bluetooth issues like voice calling and sound interruption.
Details the wiring harness connections for power, speakers, and control signals.
Explains connections for microphone, remote control adapter, and SiriusXM tuner.
General| Power Output | 50W x 4 |
|---|---|
| Bluetooth | Yes |
| USB Input | Yes |
| CD Playback | Yes |
| Display Type | LCD |
| Type | Single DIN |
| DIN Size | Single DIN |
| AUX Input | Yes |
| Subwoofer Control | Yes |
| Display Color | White |
| Button Illumination | Red |
| RDS | Yes |
| RMS Power Output | 22W x 4 |
| Radio Tuner | AM/FM |
| Preamp Outputs | 2-channel |
| Pre-amp Outputs | 2-channel |
| Audio Playback | MP3, WMA, AAC |
To Next Page