Kenwood R-2000 - Page 28

R~2-0.00
Item
Condition
6.
RECALL 1)
POWER:
ON
and
TIMER:
OFF
MODE
FUNCTION:
FREQUENCY
Press memory switches
( 1 through
0).
.........................................
Press
MODE AM, FM,
USB,
LSB
and
CW
swit-
ch
es.
7.
MEMORY
1) MODE: USB
Press
the
M.
IN
switch
and store
10,615.0
in
channel 9.
·········································
Press
the
M.
IN
switch
and store
10,635.0
in
channel
0.
8.
M.SCAN
1) M.
SCAN:
ON
2) HOLD:
ON
(Release after test)
9.
Select 1) M.
SCAN:
ON
SCAN
Press channels 1
through 3 and then
channel 2 again (twice).
10.
PG.
1)
PG.
SCAN:
ON
SCAN
2) HOLD:
ON
Turn the tuning control
clockwise and
counter:
clockwise.
28
ADJUSTMENT
Operation Check
*
The MEMO
indicator
should change
from
1through0.
*
The frequency display
should indicte
15,000.0
for
each channel.
..........................................
*
The green indicators
should
light
for
AM
and FM modes.
*
The
yellow
indicators
should
light
for
USB,
LSB
and
CW
modes.
The beep
should
be heard
when data is stored in
channels
9 and
0.
·········································
The M.
SCAN
indicator
(green) should
light
and
each
channel
should be
scanned
for
2 seconds.
The scan should
stop
and
the
HOLD indicator (red)
should
light.
When
the
HOLD
switch
is
again depressed, scanning
should resume.
"C"
should be
displayed
on
the
MEMO
indicator and
channels 1 and 3 should be
scanned continuously.
*
The
PG.
SCAN
indicator
(yellow)
should light.
*
"P"
should
be displayed
on
the
MEMO
indicator
and
the
USB
indicator
should
light.
*
The scan should
start
from
10,61 5.0
at
5 kHz
interval.
When
10,635.0
is reached, a "beep"
should sound and
the
scan
should
restart
from
10,615.0.
Scan
should stop.
The frequency should
change
from
10,615.0
to
10,635.0.
Item
Condition
11.
AUTO.M
1)
AUTO.M:
ON
12. Reset
Press channel
1 and
store
17
,000.0
then
press
channel 2 and 1.
1)
POWER: OFF
Keep
the
power
cable
connected
to.the
receiv-
er
and
disconnect
the
lithium
battery(-)
termi-
nal.
Disconnect
the
power
cable and ground
IC12
pin40.
(IC12: µPD80C49C-022)
Reconnect
the
power
cable.
POWER:
ON
AUTO.M:
ON
Disconnect, then
recon-
nect
the
power
cable.
POWER:
OFF
Reconnect
the
lithium
battery (-) terminal.
2)
POWER:ON
Disconnect
the
power
cable. Reconnect
the
power
after approxima-
tely
30
minutes.
3)
MEMORY:
1
MEMORY:
2
MEMORY: 0
Operation Check
The
AUTO.
M
indicator
(green) should
light
and
1 7
,000.0
should
be
di-
splayed.
Indication
MEMO:
E
f
:
150,055.0
Indication
MEMO:
1
f:
15,000.0
Indication
MEMO:
1
f:
15,000.0
The memory
contents
should be retained and
the
above should be displayed
Indication
MEMO:
1
f:
15,000.0
MEMO:
2
f:
15,000.0
MEMO:O
f:
15,000.0