To Next PageTo Next Page
Need help?Do you have a question about the Kenwood TK-7360H and is the answer not in the manual?
General| Brand | Kenwood |
|---|---|
| Model | TK-7360H |
| Category | Transceiver |
| Language | English |
Details the pins and functions of the ACC D-SUB 15-pin connector.
Describes the 3.5mm phone jack for external speakers.
Specifies the DC input connector details for power.
Outlines the connections and functions of the microphone jack.
Specifies the impedance for the antenna terminal.
Important safety information regarding operation, potential hazards, and warnings.
Details FCC warnings and information for digital device users.
Essential precautions to prevent fire, injury, and damage to the transceiver.
Safety warnings related to transceiver installation for passenger protection.
Cautions regarding 12V negative ground systems and power cable handling.
Lists all items included in the transceiver package for user verification.
Preparation steps and important warnings for vehicle installation.
Detailed instructions for connecting the DC power cable to the vehicle battery.
Step-by-step guide for physically installing the transceiver and connecting cables.
Safety warnings and cautions to follow during the transceiver installation process.
Identifies and explains the front and rear panel controls and connectors.
Explains the meaning and function of various icons displayed on the transceiver screen.
Lists available functions that can be assigned to programmable keys.
Instructions for powering the transceiver on/off and adjusting the audio volume.
Steps to enter and manage the transceiver's password for security.
How to navigate and select different zones and channels/group IDs.
Fundamental steps for transmitting and receiving calls on the transceiver.
Details the three types of scan modes and how to operate them.
Explains how to recall channels during scan and the functionality of Priority Scan.
How to temporarily exclude channels from the scanning sequence.
How to add or remove zones and channels from the scan list.
Explains the different types of Scan Revert channels that can be programmed.
Instructions for making DTMF calls using the keypad.
How to use and store autodial entries for quick calling.
Procedures for removing autodial entries and redialing.
How the stun function works for lost or stolen transceivers.
Explains QT/DQT tones for ignoring calls from other parties.
Details 2-tone, DTMF, FleetSync, and MDC-1200 signaling options.
How to change encode and decode tones for selected channels.
Introduces FleetSync as an alphanumeric 2-way paging function.
Guide to making and receiving selective voice calls to stations or groups.
Instructions for initiating paging calls and sending/receiving status messages.
How to receive status calls and review stored messages.
Information on sending and receiving short and long messages via PC.
Instructions for sending location data using the GPS unit.
Procedures for placing and receiving dispatch calls in trunking mode.
Steps for making and receiving telephone calls via the transceiver.
How to end a telephone call initiated through the transceiver.
How to initiate and exit emergency calls.
Details the Lone Worker safety feature and its activation.
Explains how to use Talk Around for direct communication during service interruptions.
How to activate and use the voice scrambler for secure communication.
How to use Monitor and Squelch Off to listen to weak signals or background noise.
Steps to adjust the transceiver's squelch level.
How to lock and unlock the transceiver's front panel and microphone keys.
Explains the indicator for received signal strength.
Instructions for using the Public Address system with an external speaker.
How to toggle the Horn Alert function ON or OFF.
How to configure audio output through the external speaker.
How to adjust the LCD display brightness.
Explains the TOT feature to prevent extended transmissions.
Describes the activation and use of the auxiliary port.
Details the BCL feature to prevent transmission on busy channels.
Explains PTT ID transmission and the Compander noise reduction feature.
Information on different transmit power levels available.
Details Auto Recording and Voice Memo features for recording conversations.
How to configure the transceiver for automatic responses to calls.
How to play back recorded conversations, memos, or messages.
Explains the audio announcements for zone/channel changes and function settings.
