Kenwood VR-209 User Manual

Listening to a source component
I SESE:
VOLUME CONTROL
INPUT SELECTOR
Use the input selector (INPUT SELECTOR (AUDIO, VIDEO)
to select the source you want to listen to.
The input sources change as shown below:
Selecting a source using the INPUT SELECTOR knob
@ TUNER
@ "CD" ("CD")
© "TAPE" or “MD“ ("TAPE"*)
@ "PHONO"("PHONO™*)
© “VIDEO1" ("VCR1"*)
© “VIDEO2" ("VCR2"*)
@ "VIDEO3" (“DVD"*)
Selecting a source using the AUDIO key on the remote control
oo C7] "CD" ("CD"*}
| 6 “TAPE” or "MD" (“TAPE"*)}
| €@ TUNER
~ @ “PHONO"("PHONO"*)
Selecting a source using the VIDEO key on the remote control
- @ "VIDEO" ("VCR1"*)
| @ "VIDEO2" ("VCR2"*)
| © "VIDEO3" ("DVD")
‘m @ "<--->" (Not used by this receiver.)
” Once setup codes are registered in the remote controt. the input
name display changes according to tne name of the registered
component
Example: if you register a VCR at the VIDEO 1 jacks, "VCR" appears
instead of "VIDEO 1". RC-_2..
¢ When using the remote control after initial setuo. any inputs that
have not been registered with a setup code are deteted from tne
cyclic {iSt. RC-_4_
¢ Tne INPUT SELECTOR on the front panel of tne receiver always
cycies through all inputs.
EQ Start playback from the selected source.
Ej Use the VOLUME CONTROL (VOLUME) to adjust the
volume.
VR-209-/208'KRF-V8CICD.V7E1OL ,EvKM!
Adjusting the sound
SLOPE PRESEASON MODE Dr EA Se ROR A a RRR ER RINNE EERE NEEL OSLER
VOLUME CONTROL
SOURCE DIRECT
BASS BOOST | SOUND
aes
0 =kLQO ©
Crane eed
i _ EE
PHONES MULTI CONTROL
SPEAKERS A/B
NS
_ (—- VOLUME
50 SOUND
Sn a a
Adjusting the tone
Ifa source that is not Dolby Digital is selected, you can adjust the sound
Quality when the receiver Is in the stereo mode.
@ Press the SOUND key to select the tone mode to be adjusted.
BASS: Select this to adjust the low frequency range.
(Press the SOUND key once.)
TREB: Select this to adjust the high frequency range.
(Press the SOUND key twice.)
| see Pl Tat. i it
| ke Pte es as |
© Use the MULT! CONTROL (TUNING/SKIP) to adjust the sound
quality.
* Tne bass and trepie levels are adjustable from -10 to +10in 2 step
increments.
*The adjustment ttem is displayed for approximately eight sec-
onds.
» If you used the remote control to perform the above setting, press
the VIDEO key at this point to turn off the remote control's own
adjustment mode. In this case. the input source 15 not switched.
NOR hse ots ele era Nel ee te
Once- touch low frequency emphasis 5 (bass boost)
Ifa source thatis not Dolby Digital's selected. you can adjust the sound
Quality when the receiver is in the stereo mode.
Press the BASS BOOST key.
¢Press the key once to select the maximum (+10) low frequency
emphasis setting
* Tnis key does not function when the receiver is in tne sound quality
or ambience effects adjustment mode
Switching back to the previous setting
Press the BASS BOOST key again.

Kenwood VR-209 Specifications

General

Brand	Kenwood
Model	VR-209
Category	Stereo Receiver
Language	English