1
Brew Your First Coffee
Place a mug on the drip tray plate. If
using a travel mug, remove the drip
tray and place the mug on the drip
tray base. Lift the handle and place a
K-Cup® pod in the K-Cup® pod holder.
Lower the handle completely to close
the lid.
Do not remove the foil lid on the
K-Cup® pod.
High Altitude Brewing: While holding the
brewer handle up, push down slowly on
the K-Cup® pod in the pod holder until the
bottom of the K-Cup® pod is punctured by
the exit needle.
Place Mug & Pod
Brewer Features
Frother froths milk to create your favorite latte.
SHOT button brews a shot of coffee to make delicious,
creamy lattes.
Auto Off automatically turns your brewer off 2 hours
after the last brew for energy savings.
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
2
Select your brew size. The button will remain
illuminated while brewing — about 1 minute.
Brewing is complete when the button is no
longer illuminated. Lift the handle and dispose
of the used K-Cup® pod.
The brewer will be ready to brew another cup
in about a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-
activate, lift and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the
K-Cup® pod holder. To avoid injury, do not lift the handle during the
brewing process.
Brew & Enjoy!
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Caring For Your Brewer
Regular cleaning keeps your brewer running smoothly. Always be sure to turn off and unplug your brewer before cleaning.
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Water Reservoir & Reservoir Lid
The water reservoir lid and water reservoir
should be cleaned periodically. Clean in a
dishwasher (top rack only) or hand wash. To
hand wash, use a damp, soapy, non-abrasive
cloth. Rinse the reservoir thoroughly after
cleaning. This will ensure that no cleaning
solutions remain in the area as they may
contaminate the water supply. After rinsing, fill
the reservoir with clean water and return it to
the brewer. Do not dry the inside of the water
reservoir with a cloth as lint may remain. If
needed, repeat above procedures.
NOTE: If you are using a water filter inside the water reservoir, remove it
before cleaning.
Frother
Clean immediately after each use and before
first use.
To Clean:
1. Remove frother from the base, remove
silicone ring from lid, and remove the whisk
from inside the frother.
2. Wash the silicone ring, lid, and whisk with
warm, soapy water.
3. Clean the interior of the frother with soap
and rinse with warm water. Use a soft, non-
abrasive cloth or sponge to prevent damaging
the inner coating.
4. Wipe the exterior with a soft, damp cloth.
5. Dry all parts thoroughly and reassemble for
next use.
NOTE: Frother is not dishwasher safe. Do not submerge frother in water. Only use
non-abrasive cleaning materials to prevent damage to the inner surface of the
frother.
Drip Tray
The drip tray can hold up to 8 ounces of overflow
and should be emptied and cleaned occasionally.
To remove, slide it toward you, keeping it level to
avoid spilling. Clean in dishwasher (top rack only)
or rinse and clean with a damp, soapy, lint-free,
non-abrasive cloth.
Brewer Exterior
Keep your Keurig® brewer looking its best by
cleaning the exterior from time to time. Just
clean with a damp, soapy, lint-free, non-
abrasive cloth. Never immerse the brewer in
water or other liquids.
Smart Start heats then brews in one simple process. No need
to wait for the brewer to heat before selecting brew size.
Power on your brewer, place mug, insert a K-Cup® pod, and
lower the handle. Then, select your brew size. The brewer will
heat, then automatically begin brewing.
To Next Page
Loading...
