Key Automation RAY2524 - Models and Characteristics; Product Overview; Preliminary Checks; Product Description

10
EN
2 - PRODUCT OVERVIEW
2.1 - Description of the product
The RAY gear motors are destined to be installed in systems for the
automation of gates with hinged doors.
The RAY gear motors have been designed and constructed to be
tted onto hinged doors within the weight limits indicated in the
technical specications table.
The use of gear motors for applications which differ from those
indicated above is prohibited.
2.2 - Model and technical characteristics
3 - PRELIMINARY CHECKS
Before installing this product, verify and check the following steps:
- Check that the gate or door are suitable for automation
- The weight and size of the gate or door must be within the maxi-
mum permissible operating limits specied in Fig. 2
- Check the presence and strength of the security mechanical stops
of the gate or door
- Check that the mounting area of the product is not subject to ood-
ing
- Conditions of high acidity or salinity or proximity to heat sources
could cause malfunction of the product
- Extreme weather conditions (for example the presence of snow,
ice, high temperature range, high temperatures) may increase the
friction and therefore the force required for the handling and initial
starting point may be higher than under normal conditions.
- Check that the manual operation of gate or door is smooth and
friction-free and there is no risk of derailment of the same
- Check that the gate or door are in equilibrium and stationary if left
in any position
- Check that the power line to supply the product is equipped with
proper grounding safety and protected by a magnetothermal and
differential security device
- Provide the power system with a disconnecting device with a gap
of contacts enabling full disconnection under the conditions dictated
by the overvoltage category III.
- Ensure that all materials used for the installation comply with cur-
rent regulations
Code Description
RAY2524 Gear motor for hinged doors with max length 2.5 m and weight 250 Kg, 24 Vdc
RAY2524E Gear motor for hinged doors with max length 2.5 m and weight 250 Kg with encoder, 24 Vdc
RAY4024 Gear motor for hinged doors with max length 4 m and weight 300 Kg, 24 Vdc
RAY4024E Gear motor for hinged doors with max length 4 m and weight 300 Kg with encoder, 24 Vdc
RAY40 Gear motor for hinged doors with max length 4 m and weight 300 Kg, 230 Vac
RAY40110 Gear motor for hinged doors with max length 4 m and weight 300 Kg, 110 Vac
TECHNICAL DATA
MODELS
RAY2524
RAY2524E
RAY4024
RAY4024E
RAY40 RAY40110
TECHNICAL SPECIFICATIONS
Speed 2,6 cm/s 1,5 cm/s 1,6 cm/s 1,6 cm/s
Thrust force 1500 N 2000 N 2000 N 2000 N
Working cycle 80% 80% 40% 40%
Opening time at 90° adjustable adjustable 25 sec 25 sec
Working stroke 415 mm 415 mm 415 mm 415 mm
Control board 14AB 14AB2 CT202 CT202V120
Power supply 24 Vdc 24 Vdc 230 Vac 110 Vac
Absorption 3,5 A 5 A 1,2 A 2,2 A
Engine power 85 W 120 W 280 W 280 W
Capacitor - - 8 µF 20 µF
Thermoprotection - - 150 °C 150 °C
Integrated lights yes yes - -
Degree of protection IP44 IP44 IP44 IP44
Dimensions (L - P - H) 844-100-104 mm 844-100-104 mm 844-100-104 mm 844-100-104 mm
Weight 6 Kg 8 Kg 8 Kg 8 Kg
Operating temperature -20°+55°C -20°+55°C -20°+55°C -20°+55°C
Leaves maximum weight 500 Kg 600 Kg 600 Kg 600 Kg