EasyManua.ls Logo

Kingsman ZDV6000 - User Manual

Default Icon
59 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
Warning: Improper installation, adjustment, alteration, service or maintenance can cause property
damage, personal injury or loss of life. Refer to this manual. Installation and service must be performed by
a qualified installer, service agency or the gas supplier.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
What To Do If You Smell Gas
Do not try to light any appliance.
Extinguish any open flame.
Do not touch any electrical switch.
Do not use any phone in your building.
Immediately call your gas supplier from a neighbour's phone.
If you can not reach your gas supplier, call the fire department.
For Propane Horizontal installations the venting must be a minimum of one foot vertical off the flue before
going horizontal.
Installation Instructions
Model Number ZDV6000, ZDV3320
MQRB3328
Zero Clearance Direct Vent Gas Fireplace
Stock #’s ZDV3320N, ZDV3320LP, ZDV3320NE, ZDV3320LPE, are
Certified to: ANSI Z21.50b-2009, CSA 2.22b-2009, CGA 2.17-M91
Stock #’s ZDV6000N, ZDV6000LP, MQRQB3328N, MQRB3328LP
ZDV6000NE, ZDV6000LPE, MQRQB3328NE, MQRB3328LPE are
Certified to: ANSI Z21.88-2009, CSA 2.33-2009, CGA 2.17-M91
Printed in Canada May 8, 2012 Part # 33DV-MAN-II
FOR YOUR SAFETY
Read this complete manual before beginning installation.
These instructions must be kept with the unit for future reference.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for
use with other gases, unless a certified kit is used.
A Division of R-Co. Inc.
2340 Logan Avenue
Winnipeg, Manitoba, Canada R2R 2V3
Ph: (204) 632-1962
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

Table of Contents

Questions and Answers

  • F
    frederickreyesAug 6, 2025
    Why won't the pilot light stay lit on my Kingsman Indoor Fireplace?
    • C
      Christina DavisAug 7, 2025
      If the pilot light won't stay lit even after following the lighting instructions, it could be due to: * A defective thermocouple. Ensure the pilot flame impinges on both the generator and thermocouple. Try cleaning and adjusting the pilot for maximum flame impingement. If it still won't hold, replace the thermocouple, tightening it by hand plus an additional 1/8 turn. * A defective valve magnet. If replacing the thermocouple doesn't solve the issue, the valve may need to be replaced.
  • C
    colleendavisAug 11, 2025
    How to fix frequent pilot outage problem in Kingsman Indoor Fireplace?
    • C
      Christopher LindseyAug 11, 2025
      Frequent pilot outages in your Kingsman Indoor Fireplace can often be attributed to the pilot flame itself. If the pilot flame is either too low or is being blown too high, it can cause the pilot safety to drop out. To resolve this, you should clean and adjust the pilot flame to ensure maximum flame impingement on both the generator and the thermocouple.
  • D
    danielle05Aug 17, 2025
    How to fix spark igniter that will not light in Kingsman Indoor Fireplace?
    • S
      Shawn RosarioAug 17, 2025
      If the spark igniter on your Kingsman Indoor Fireplace isn't lighting, check for a spark at the electrode and pilot. If there's no spark and the electrode wire is properly connected, you may need to replace the igniter. If there is a spark, use a match to light the pilot. If the pilot lights, turn it off and push the red button again. If the pilot still won't light, check the gap at the electrode and pilot; it should be 1/8” to 1/4” to ensure a strong spark.
  • C
    Cody PriceAug 21, 2025
    What to do if flame lifts off burner and goes out in Kingsman Indoor Fireplace?
    • B
      Bonnie PopeAug 21, 2025
      If the flame lifts off the burner and extinguishes in less than 30 seconds, the inner 4” liner may have detached from the flue or termination, causing flame starvation. Reattach the 4” liner to the flue or termination using screws, silicone, and clamps as described in the manual.
  • J
    Joseph MillerAug 27, 2025
    Why flame lifts off burner on one side in Kingsman Indoor Fireplace?
    • M
      Mary JonesAug 27, 2025
      If the flame lifts off the burner on one side while the rest remains lit, it's likely due to improper installation of the firebrick, possibly leaning. Make sure to position the firebrick against the firebox walls and secure it using brick clips attached to the inner side of the firebox.
  • J
    Jeremy WintersNov 1, 2025
    What to do if pilot burning but no gas to burner in my Kingsman Indoor Fireplace?
    • M
      Mark RodriguezNov 1, 2025
      If the pilot light is on, the valve knob is in the “ON” position, and the wall switch is also “ON”, but there's no gas going to the burner, here's what you can check: 1. Ensure the wall switch and its wiring are properly connected. You can bypass the wall switch by using a jumper wire across its terminals. If the burner then ignites, the wall switch is defective and needs replacement. If it doesn't help, jump the wires across the wall switch wires at the valve. If the burner comes on, the wires are faulty or connections are bad. 2. Test the generator with a millivolt meter at the gas valve terminals. It should read a minimum of 325 millivolts while holding the valve knob depressed in the pilot position and the wall switch in the “off” position. Replace the generator if the reading is be...

Summary

FOR YOUR SAFETY

What To Do If You Smell Gas

Procedure for responding to the smell of gas, including actions to take and who to contact.

Pre-installation Questions and Answers

About curing of the paint

Explains the paint curing process, necessary initial firings, and precautions during curing.

Why does my fireplace or stove give off odour?

Details common causes for initial odors from the fireplace and recommendations for dissipation.

Noise coming from the fireplace?

Explains that noises from expansion/contraction are normal and do not affect operation.

Operating Instructions

Mobile Home;Manufactured Housing Installation

Warnings, Installations and Operations

Installation Regulations

Specifies installation requirements according to local building codes and national fuel gas codes.

Installation Requirements for the Commonwealth of Massachusetts

Operations and Maintenance Instructions

Locating your Appliance

Fireplace Dimensions

ZDV3320, ZDV6000 & MQRB3328 with Louvers

Provides dimensional diagrams for fireplaces with louvers, including height, width, and depth.

ZDV3320, ZDV6000 & MQRB3328 with Clean View Kit

Provides dimensional diagrams for fireplaces with a Clean View Kit, including clearances.

Framing for your Gas Fireplace

ZDV3320, ZDV6000 & MQRB3328 with Louvers

Details framing requirements and clearances for fireplaces with louvers, including vent pipe clearances.

ZDV3320, ZDV6000 & MQRB3328 with Clean View Kit

Details framing requirements and clearances for fireplaces with Clean View Kit, including vent pipe clearances.

Z33 CVCK - Framing and Facing Requirements

Z33 CVCK - with Wall Surround

Specifies framing and installation requirements when using the Z33CVCK with a wall surround.

33-MVHS Heat Shield Installation

How To Install Clean View Kit (Cvck)

CLEARANCES - Mantels & Surrounds

Clearance to Combustibles

MQ33 SW Wall Mount Surround Installation

Fan Kit Installation

Split Receptacle - Fan Speed Control Outside of Fireplace

Installing Fireplace Panels

Installing Brick Panel

Step-by-step instructions for installing brick panels inside the fireplace firebox.

Installing Porcelain Panel

Step-by-step instructions for installing porcelain panels inside the fireplace firebox.

MQRB3328 Liner Panels

Removal of Back Panel and False Bottom

Procedure for safely removing the back panel and false bottom from the MQRB3328 fireplace.

Installation of MQRB3328 Liner Panels

Instructions for installing the back and side liner panels for the MQRB3328 model.

Gas Line Installation

General Glass Information

Glass Cleaning

Guidelines for cleaning the fireplace glass, including frequency and methods.

Glass Replacement

Instructions for safely removing and replacing the fireplace glass door.

Millivolt System, Lighting, and Burner Control

Burner System Maintenance

Monthly Flame Inspection

Guidance on monthly inspection of the flame pattern and pilot flame for proper operation.

Conversion Kit Instructions - PART A

Gas Conversion -Part A - ZDV3320;ZDV6000

Details conversion steps for ZDV3320/ZDV6000 models, focusing on orifice and air shutter adjustments.

Gas Conversion -Part A - MQRB3328

Details conversion steps for MQRB3328 models, focusing on orifice and air shutter adjustments.

Gas Conversion for Top Convertible Pilot (Series 019065 X) - PART B

Gas Conversion for Modulator - PART C

IPI Electronic Ignition System

Overview

Introduces the IPI system, its modes (Standing-Pilot vs. Intermittent-Pilot), and advantages.

Components

Lists and describes the key components of the IPI system, including the main module, valve, and covers.

Electronic Ignition Lighting Instructions

Trouble Shooting The Gas Control System

Field Conversion for ZDV6000 - VF125 - VF130

LOGC5 or LOGF5 Setup for Model ZDV6000

LOGC6 Setup for Model ZDV6000

MQROCK1;MQRSP6 Setup for Model ZDV6000

LOGC42;LOGC43 Placement Guidelines for Model ZDV3320

LOGC44 Placement Guidelines for Model ZDV3320

MQROCK1;MQRSP3 Setup for ZDV3320

Accessories Available for Skyline & ZDVRB3622 Ribbon Burner Units

ULK2 Universal Light Kit Installation

Vent Termination

Termination Clearances

Specifies minimum clearances required around the vent termination plate to prevent fire hazards.

General Venting Information

Provides information on approved venting methods and components for the fireplace.

General Vent Installation Information

RIGID OR HARD PIPE Venting

Instructions and guidelines for installing rigid or hard vent pipes, including adapters and sealant.

Flex Pipe Venting

Instructions for installing flexible vent pipes, including expansion, support, and sealing.

Installation Of Side Wall Venting

Step-by-step guide for installing side wall venting, including hole cutting and thimble installation.

Venting Routes and Components

How To Use The Vent Table

Venting Straight Up Through Roof

Roof Flashing

Guidance on selecting and installing the correct roof flashing based on roof pitch.

Using Flex Bends

Instructions for using flexible pipe bends, including support and clearance requirements.

Parts List

Glass Safety

Termination Cap Safety

LIMITED LIFETIME WARRANTY

Kingsman ZDV6000 Specifications

General IconGeneral
BrandKingsman
ModelZDV6000
CategoryIndoor Fireplace
LanguageEnglish

Related product manuals