The Kingwo MT200 is a smart GPS tracker designed for various tracking and monitoring applications. It offers a comprehensive set of features for accurate positioning, driving behavior analysis, and alarm functions, making it suitable for fleet management, personal vehicle tracking, and other IoT scenarios.
Function Description
The MT200 primarily functions as a GPS tracker, providing real-time location data and historical tracking. It supports multiple positioning technologies including GPS, AGPS, and LBS, ensuring accurate positioning even in challenging environments. The device is equipped with a built-in high-sensitive G-sensor accelerometer, which enables advanced features like driving behavior monitoring, including speeding, hard acceleration, hard deceleration, and cornering alarm.
Key functions include:
- Data Upload: The device can be configured to upload data packets to a backend server at a certain time interval, with a default setting of upload by time.
- History Data Storage: When the device enters a GPS blind area, it stores GPS data for up to 15 seconds as default. Maximum 1000 pieces of data can be stored, configurable from 5 to 7200 seconds.
- Cornering Compensation: Detects the vehicle's driving direction and uploads a packet extra to make the driving trace more accurate, especially during turns.
- LBS (Location Based Service) Support: If GPS is unavailable, the device automatically switches to LBS mode, acquiring LBS station IDs and interpreting the specific location on the map.
- AGPS (Assisted GPS) Support: Supports AGPS for faster positioning and improved accuracy.
- Alarm Functions: A wide range of alarms are supported, including:
- Low Voltage Alarm: Notifies when the battery voltage is too low (0-11V or 19-22V).
- Over Speed Alarm: Triggers when the vehicle speed exceeds a preset value.
- Driving Behavior Alarm: Detects speeding, hard deceleration, hard acceleration, and cornering.
- Vibration Alarm: Alerts after 10 minutes of ignition off (Arm range 1-20 minutes) or generates vibration (Delay range 1-10 minutes) without ACC connected.
- Turn Over Alarm: Reports if the device turns over.
- Towing Alarm: An alarm is generated if the device is set to a displacement of more than 100 meters (message mode prompt), and the alarm information is reported when the displacement radius exceeds 100 meters when the device is turned off.
- Wire Cut Off Alarm: Connects to a power off relay for power and fuel cut off function in case a car stolen happens.
- GPS Error Alarm: Reports if the GPS module is working abnormally.
- Device Removal Alarm: Utilizes a built-in light sensor to detect if the device is removed from its installation location.
- Intelligent Functions:
- Power Save: The device has a built-in high-sensitivity G-sensor accelerometer that monitors the vehicle for motion in real time. When no motion is detected for a long time, the device automatically enters the power saving state, turning off the GPS/BD module and GSM enters the heartbeat return mode.
- Self-Diagnosis: Performs self-diagnosis and reports error messages to the backend if there is malfunction regarding GPS and GSM.
- Static Drift Suppression: A built-in high-sensitivity G-sensor accelerometer and a complete positioning data-filtering algorithm filter out most of the static drift data to ensure the accuracy of GPS data.
- Mileage Calculation: Calculates mileage based on speed from GPS and vehicle positioning data.
- Remote Configuration: Allows remote setting of device parameters including IP, center number, and various monitoring parameters via the backend or SMS.
- Remote Upgrade (OTA): Supports remote firmware upgrades via GPRS.
- Dual IP or Domain: Supports dual IP connection between the primary server and the standby server.
- GT800 and JT808 Protocol: Compatible with GT800 protocol and JT808 protocol, with protocol switch by SMS or Bluetooth setting.
- Bluetooth Function: Built-in Bluetooth for configuration and sensors connecting (e.g., Bluetooth fuel sensor).
Important Technical Specifications
- Physical:
- Dimension: 75*40*13mm
- Weight: 45±3g
- Cellular:
- GSM Module: Quectel MC25
- Working Frequency: 850/900/1800/1900MHz
- Network Protocol: Embedded TCP/IP stack
- Sensitivity: -107dBm@850/900MHz, -106dBm@1800/1900MHz
- Output Power: Class 4 (2W)@850/900MHz, Class 1 (1W)@1800/1900MHz
- GPRS Data: GPRS Class 10, Mobile Station Class B
- GPS:
- Channels: 50
- Sensitivity: -147dBm
- Position Accuracy: 5-10m
- Accuracy (CEP): 5m
- Cold Start: <27s
- Hot Start: <1s
- Bluetooth:
- Power:
- Input Voltage: 9-100V
- Battery: NI-MH AAA 3.6V/90mA, 2 hours working time based on 2-3 minutes upload
- Average Current: <30mA (DC 12V)
- Maximum Current: <10mA (DC 12V)
- Digital Input (2): Ignition detect and Air condition status detect
- Interface:
- Digital Output (1): Relay
- Analog Input 1: Voltage range: 0-36V
- GSM Antenna: Internal High Gain
- GPS Antenna: Internal High Gain
- SIM: Microsim
- Environmental Parameter:
- Indicator: 2 status LEDs (Green: GPS, Red: GSM)
- Memory: 1000 packets
- Working Temperature: -20°C ~ +70°C
- Humidity: 5% ~ 95% (no fog)
- Ingress Protection Rating: IP65
Usage Features
The MT200 is designed for ease of installation and configuration.
- SIM Installation: Open the top cover, insert the prepared SIM card into the SIM cardholder, and ensure the SIM card button is in place. The SIM card must have GPRS function enabled.
- Main Unit Power On: After installing the SIM card, turn the battery switch to the ON position. The red light starts to blink, indicating the device is powered on.
- Wiring Diagram: A detailed wiring diagram is provided for connecting the device to the vehicle's electrical system, including Red (VCC), Black (GND), Orange (ACC), White (Lock/Relay), and Blue (IO).
- Parameter Setting by SMS: The device can be configured using SMS commands for various parameters such as APN, IP address, upload intervals, alarm settings (towing, vibration, speed, cornering), Bluetooth password, and more.
- Parameter Setting by Android APP via Bluetooth: Users can download the "Track Sense" app, connect to the device via Bluetooth (default password 1234#), and send commands to configure parameters.
- Recommended Installation Place: The manual suggests various installation locations for optimal performance, including under the back seat, inside the headlight cover/around the speedometer, under the rear windshield, under the front windshield, and around the dashboard.
- Software: Kingwo provides a web-based software (www.itracksense.com) and a smart phone application (Track Sense) for tracking and management. Default credentials are provided for the web-based software.
Maintenance Features
- Remote Firmware Upgrade (OTA): The device supports over-the-air firmware updates, allowing for easy maintenance and feature enhancements without physical access.
- Self-Diagnosis: The MT200 can perform self-diagnosis and report errors, aiding in troubleshooting.
- Device Removal Alarm: The built-in light sensor helps detect if the device has been tampered with or removed, contributing to its security and ensuring continuous operation.
- Power Save Mode: The intelligent power save mode helps conserve battery life, reducing the frequency of battery maintenance or replacement.
The MT200 is a robust and versatile GPS tracker, offering a blend of essential tracking functionalities with advanced monitoring and alarm capabilities, all within a compact and durable design.
Need help?
To Next Page
General