Why my KitchenAid Blender doesn't turn on?
If your KitchenAid Blender doesn't run at all, and no lights are showing, start by ensuring it's properly plugged into a grounded, three-prong outlet. Then, check the power outlet to confirm it's working correctly, inspecting the breaker and wiring if necessary. If the power cord is damaged, it should be replaced. Finally, a faulty UI switch could also be the culprit, and it may need replacement.
How to fix KitchenAid Blender jar leaking?
If your KitchenAid blender jar leaks, you might be overfilling it, causing ingredients to push out. Try reducing the amount of ingredients you're blending. Also, inspect the jar and lid for any damage, and replace the jar assembly or lid if they are faulty or broken.
How to reset KitchenAid Blender UI when light is flashing quickly?
If your KitchenAid Blender powers on and the UI light is flashing quickly, it indicates that the blender UI needs to be reset. To do this, turn the dial to the “OFF” position and then select the desired operating setting. Once reset to the desired setting, press “START.”
Why does my KitchenAid 5KSB5080 Blender stop while blending?
If your KitchenAid Blender stops while blending, first, rotate the selection dial to the “OFF/O” position, then rotate to your desired setting, and press START/PAUSE. Also, the blender automatically shuts off after about 2 minutes on Variable Speed. To reset, turn the dial to “OFF/O”, then back to your setting, and press START/PAUSE. If the LED is flashing rapidly, the pitcher might not be fully in place, or the blender may be in “sleep mode” and needs to be reset to “OFF/O”. Follow the “Error mode” instructions in this case.
What to do if my KitchenAid Blender is not ready for blending and the LED is flashing rapidly?
If your KitchenAid Blender isn't blending and the LED flashes rapidly, it could be due to several reasons. First, ensure the pitcher is correctly in place by rotating the knob to “OFF/O”, properly positioning the pitcher, selecting your desired setting, and pressing the START/PAUSE button. Alternatively, the blender might be jammed. In this case, press START/PAUSE, unplug the power cord, remove the pitcher, and use a scraper to free the blades by breaking up or removing contents at the bottom. Then, rotate the knob to “OFF/O” before restarting.
What to do if KitchenAid 5KSB5080 Blender blades do not spin properly?
If the KitchenAid Blender blades do not spin properly, first, check the blender jar assembly for any faults. With the jar removed, carefully inspect the blade movement; if it doesn't turn freely, replace the jar. Also, ensure the jar is correctly inserted into the blender base and engaged with the jar release handle. If the blade moves freely and the jar is properly inserted, but the blades still don't spin when the blender is running, the drive belt may be broken or loose and needs replacement.
What to do if KitchenAid 5KSB5080 Blender does not run at some selections?
If your KitchenAid Blender doesn't run at some selections, the UI Dial/Switch Assembly might be faulty and needs replacement. Alternatively, the electrical control board could be faulty, requiring its replacement.
What to do if KitchenAid 5KSB5080 Blender is jammed?
If your KitchenAid Blender is in error mode because it's jammed, press START/PAUSE, then unplug it. Remove the pitcher from the base, and use a scraper to free the blades by removing contents at the bottom. To restart, turn the knob to “OFF/O” and then to your desired setting, and press START/PAUSE.
What to do if KitchenAid 5KSB5080 Blender shows error mode?
If your KitchenAid Blender is in error mode, rotate the knob to the “OFF/O” position. Ensure the pitcher is properly in place. Select your desired setting and press the START/PAUSE button. If the blender is jammed, press START/PAUSE, then unplug the power cord, remove the pitcher, and clear any obstructions from the blades. To restart, rotate the knob to the “OFF/O” position, then select your setting and press START/PAUSE.
Why does my KitchenAid 5KSB5080 vibrate?
If your KitchenAid Blender vibrates on the work surface, start by checking the feet for wear, dirt, or damage; replace them if necessary and clean any dirt with mild soap and water. Ensure the jar is fully seated to the tab and engages with the jar release handle. Also, inspect the belt for proper alignment to the pulleys by removing the base.
General| Jar Material | Glass |
|---|---|
| Blade Material | Stainless Steel |
| Number of speeds | Variable |
| Voltage | 220-240 V |
| Power | 500 watts |
| Jar Capacity | 1.4 L |
| Speed Settings | Variable |
| Capacity | 1.4 L |
| Motor Power | 500 watts |
To Next Page
