Klein Tools ET200 - User Manual

To Next Page

Instruction

Manual

Instruction

Manual

ENGLISH

www.kleintools.com

F o r P r o f e s s i o n a l s . . . S i n c e 1 8 5 7

ET200

• AC/DC

VOLTAGE

TO 600V

• CONTINUITY

FUNCTION

• WORKLIGHT

• LIGHT, VIBRATION, SOUND INDICATORS

• CAT IV 600V SAFETY RATING

• MODERN SOLID-STATE DESIGN

ENGLISH

600

480

277

240

208

120

ET200

Instruction Manual

GENERAL SPECIFICATIONS

The Klein Tools ET200 is a solid-state electrical tester. It measures AC/DC

voltage, tests continuity, and features a bright LED worklight.

• Voltage Level Indicators: 12, 24, 48, 120, 208, 240, 277, 480, 600

• Voltage Type Indicators: AC, DC Positive, DC Negative

• AC Frequency: 45Hz to 66Hz

• Maximum Voltage To Earth Ground: 600V RMS

• Maximum Measurable Voltage: 600V RMS (displayed by LEDs)

• Input Impedance: 15kΩ on connection, up to 150kΩ steady-state.

• Continuity: < 270kΩ

• Usage Duty Cycle (Above 277V): 1 minute on, 5 minutes off

• Accuracy: 70% to 100% of indicated voltage

• Battery Type: 3 x AAA

• Operating Altitude: 2000m

• Relative Humidity: 0°C to 30°C (32°F to 86°F) 90%

30°C to 40°C (86°F to 104°F) 75%

40°C to 55°C (104°F to 131°F) 45%

• Operating Temperature: 0°C to 55°C (32°F to 131°F)

• Storage Temperature: 0°C to 55°C (32°F to 131°F)

• Dimensions: 7.375 x 2.375 x 1.25”

• Weight: 8.1oz.

• Safety: CSA C22.2-1010.1, IEC 61010-1, Pollution Degree II

• CAT Rating: CAT IV 600V, CAT III 1000V

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

• Before each use, verify meter operation by measuring

a known voltage or current.

• Never use the meter on a circuit with voltages that exceed the

category based rating of this meter.

• Do not use the meter during electrical storms, or in wet weather.

• Do not use the meter or test leads if they appear to be damaged.

• Ensure meter leads are fully seated, and keep ﬁngers away from

the metal probe contacts when making measurements.

• Do not open the meter to replace batteries while the probes

are connected to a voltage source.

• Use caution when working with voltages above 60V DC,

or 25V AC RMS. Such voltages pose a shock hazard.

• Shut off and lock out power before testing continuity.

• Always adhere to local and national safety codes. Use individual

protective equipment to prevent shock and arc blast injury where

hazardous live conductors are exposed.

Need help?

Do you have a question about the Klein Tools ET200 and is the answer not in the manual?

Summary

General Specifications

Safety Warnings

Symbols and Categories

Feature Details

Details on indicators, worklight, ghost voltages, and lead spacing for the electrical tester.

Operating Instructions

Guidelines for operating the tester, including voltage measurement procedures and auto-on functionality.

Continuity Testing

GFCI Testing

Procedure for testing GFCI receptacles using the voltage tester.

Battery Replacement

Instructions for replacing the AAA batteries in the ET200 tester.

Product Care and Support

Warranty Information

Details the two-year limited warranty for the electrical tester and exclusions.

Cleaning and Storage

Recommendations for cleaning, storing, and preparing the instrument for use.

Disposal and Customer Service

Information on proper disposal of equipment and contact details for customer support.