To Next Page
R
Ricky GordonAug 22, 2025
What to do if Kohler Marine Equipment battery is weak or dead?
- AAlexis TaylorAug 22, 2025
If the battery is weak or dead, recharge or replace it. The spec sheet provides recommended battery CCA rating.
What to do if Kohler Marine Equipment battery is weak or dead?
If the battery is weak or dead, recharge or replace it. The spec sheet provides recommended battery CCA rating.
How to reset emergency stop switch on Kohler 70EFOZ?
If the emergency stop switch is activated, reset it.
What to do if Kohler 70EFOZ Marine Equipment experiences low coolant level shutdown?
If there is a low coolant level shutdown, restore the coolant to the normal operating level.
How to fix clogged air openings in Kohler 70EFOZ Marine Equipment?
If the air openings are clogged, clean them.
How to clean seawater strainer in Kohler 70EFOZ Marine Equipment?
To resolve a clogged or restricted seawater strainer, clean the strainer.
What to do if AC output circuit breaker open in Kohler Marine Equipment?
If the AC output circuit breaker is open, reset the breaker and check for AC voltage at the generator side of the circuit breaker.
What to do if Kohler 70EFOZ Marine Equipment oil level low?
If the oil level is low, restore it and inspect the generator set for oil leaks.
What to do if Kohler 70EFOZ Marine Equipment controller fuse blown?
If the controller fuse is blown, replace it. If the fuse blows again, troubleshoot the controller.
What to do if Kohler 70EFOZ Marine Equipment fuel tank is empty?
If the fuel tank is empty or the fuel valve is shut off, add fuel and move the fuel valve to the ON position.
General| Brand | Kohler |
|---|---|
| Model | 70EFOZ |
| Category | Marine Equipment |
| Language | English |
Record generator set model, spec, serial, and accessory details.
Record engine manufacturer, model, and serial numbers.
Covers risks of accidental startup, battery acid, and explosive gases.
Warns about fuel system fires, backfires, and carbon monoxide risks.
Addresses fuel vapors, noise, and electrical shock hazards.
Covers safety for electrical loads, welding, and hot components.
Warns about injury risks from moving components and airborne particles.
Advises on hardware, ESD, fuse replacement, and saltwater damage prevention.
Identifies maintenance parts and service recommendations for generator sets.
Lists available literature such as installation and service manuals for generator sets.
Explains how specification sheets provide generator and engine data.
Details the alternator, PMG excitation system, and voltage regulator operation.
Illustrates and labels key service points on the generator set.
Describes kits and components like annunciator, safeguard breaker, and run relay.
Lists essential checks and inspections to perform before generator set startup.
Advises on seasonal inspections, recommending Coast Guard Auxiliary involvement.
Shows angular operation limits for generator set units.
Notes compliance requirements for operation in European Union member countries.
Provides instructions for weekly operation and inspection of the generator set.
Details the operation of the Decision-Maker 3+ controller with prime power mode.
Describes the various controls and indicators on the Decision-Maker 3+ controller.
Explains the fuses and terminal strips on the Decision-Maker 3+ controller circuit board.
Defines possible auxiliary fault lamp conditions and their meanings.
Outlines procedures for local and automatic starting of the generator set.
Provides procedures for normal and emergency stopping of the generator set.
Explains how to enable and use the prime power mode for reduced battery drain.
Lists automatic shutdown conditions for the generator set and their causes.
Details the steps to restart the generator set after a fault shutdown.
Explains how to reset the emergency stop switch and restart the generator set.
Details the operation of the Expanded Decision-Maker 1 controller.
Describes the controls and indicators for the Expanded Decision-Maker 1 controller.
Outlines procedures for starting the generator set with the Expanded controller.
Provides procedures for stopping the generator set with the Expanded controller.
Lists automatic shutdown conditions for the Expanded controller.
Details restarting the generator set after a fault shutdown with the Expanded controller.
Details the operation of the Standard Decision-Maker 1 controller.
Describes the controls and indicators for the Standard Decision-Maker 1 controller.
Outlines procedures for starting the generator set with the Standard controller.
Provides procedures for stopping the generator set with the Standard controller.
Lists automatic shutdown conditions for the Standard controller.
Details restarting the generator set after a fault shutdown with the Standard controller.
Covers general safety and maintenance practices for the generator set.
Provides a schedule for routine maintenance tasks based on operating hours.
Details cooling system maintenance procedures.
Details the procedure for inspecting the siphon break to prevent seawater entry.
Guides on checking and replacing the seawater pump impeller.
Outlines points to inspect in the exhaust system for leaks, corrosion, and blockages.
Provides procedures for preparing the generator set for storage.
Details steps to prepare the lubricating system for long-term storage.
Outlines steps to prepare the cooling system for long-term storage.
Details steps to prepare the fuel system for long-term storage.
Guides on cleaning and protecting the generator set exterior during storage.
Provides instructions for storing the battery after other storage procedures.
