Tools and Aids
24 24 690 01 Rev. SKohlerEngines.com
TOOLS
Description Source/Part No.
Mobile KDS Gen 2 (Wireless) Module (New CAN bus/ETB capable)
Replaces the previous Kohler 25 761 45-S for mobile Android or iOS EFI diagnostics.
Components of 25 761 55-S
7 Pin to DB9 Cable
7 Pin to 4 Pin Adapter
K-Line Adapter Jumper Lead Wiring Harness
Kohler 25 761 55-S
Kohler 25 761 48-S
Kohler 25 761 53-S
Kohler 25 176 23-S
Mobile (Wireless) CAN bus Cable Upgrade Kit
Updates the previous Kohler 25 761 45-S Mobile (wireless) Android or iOS tool to
allow CAN bus/ETB communications and the ability to perform diagnostics.
Components of 25 761 56-S
7 Pin to DB9 Cable
7 Pin to 4 Pin Adapter
K-Line Adapter Jumper Lead Wiring Harness
Kohler 25 761 56-S
Kohler 25 761 48-S
Kohler 25 761 53-S
Kohler 25 176 23-S
Replacement Cable and Adapter Kit
For laptop/desktop PC or Mobile (Wireless).
Components of 25 761 57-S
7 Pin to DB9 Cable
7 Pin to 4 Pin Adapter
Kohler 25 761 57-S
Kohler 25 761 48-S
Kohler 25 761 53-S
Flywheel Puller
For properly removing fl ywheel from engine.
SE Tools KLR-82408
Flywheel Anchor Bolts, Washers, Nuts Tool
Used with Flywheel Puller for properly removing fl ywheel from 5400 Series engine.
Kohler 25 086 753-S
Hose Removal Tool, Dual Size/End (also available in EFI Service Kit)
Used to properly remove fuel hose from engine components.
Kohler 25 455 20-S
Ignition System Tester
For testing output on all systems, including CD.
Kohler 25 455 01-S
Inductive Tachometer (Digital)
For checking operating speed (RPM) of an engine.
Design Technology Inc.
DTI-110
Oil Pressure Test Kit
For testing/verifying oil pressure on pressure lubricated engines.
Kohler 25 761 06-S
Rectifi er-Regulator Tester (120 volt current)
Rectifi er-Regulator Tester (240 volt current)
For testing rectifi er-regulators.
Components of 25 761 20-S and 25 761 41-S
CS-PRO Regulator Test Harness
Special Regulator Test Harness with Diode
Kohler 25 761 20-S
Kohler 25 761 41-S
Design Technology Inc.
DTI-031R
DTI-033R
Spark Advance Module (SAM) Tester
For testing SAM (ASAM and DSAM) on engines with SMART-SPARK
™
.
Kohler 25 761 40-S
Starter Servicing Kit (All Starters)
For removing and reinstalling drive retaining rings and brushes.
Individual component available:
Starter Brush Holding Tool (Solenoid Shift)
SE Tools KLR-82411
SE Tools KLR-82416
Stepper Motor Controller Tool
For testing operation of stepper motor/Digital Linear Actuator (DLA).
Kohler 25 455 21-S
Jumper Lead Tool
For use with Stepper Motor Controller Tool to test rotary stepper motor.
Kohler 25 518 43-S
Triad/OHC Timing Tool Set
For holding cam gears and crankshaft in timed position while installing timing belt.
Kohler 28 761 01-S
Valve Guide Reamer (K and M Series)
For properly sizing valve guides after installation.
Design Technology Inc.
DTI-K828
Valve Guide Reamer O.S. (Command Series)
For reaming worn valve guides to accept replacement oversize valves. Can be used
in low-speed drill press or with handle below for hand reaming.
Kohler 25 455 12-S
Reamer Handle
For hand reaming using Kohler 25 455 12-S reamer.
Design Technology Inc.
DTI-K830
To Next Page
Loading...
