Konica Minolta bizhub 215 User Manual (English)

Other manuals for Konica Minolta bizhub 215

User Guide166 pages

Start Guide4 pages

Quick Guide126 pages

Installation Manual8 pages

Questions and Answers:

C
Cathy PayneAug 23, 2025
What to do if my Konica Minolta bizhub 215 All in One Printer says 'Document JAM on machine'?
- J
  Joshua TorresAug 23, 2025
  If your Konica Minolta All in One Printer displays 'Document JAM on machine', it indicates a paper jam inside the ADF or that jammed paper hasn't been completely removed. Here's what you should do: * Open the Left Cover and the ADF. * Remove all jammed paper. When all jammed paper is removed, the memory size (in %) should return to the initial value.
J
Jessica ScottSep 2, 2025
What does '[DISCONNECT]' mean when using USB memory with Konica Minolta bizhub 215?
- T
  Timothy BenjaminSep 2, 2025
  The '[DISCONNECT]' message on your Konica Minolta All in One Printer indicates that the connection to the USB memory has been interrupted. Check that the USB memory is connected correctly.
M
Meghan FowlerAug 31, 2025
How to fix '[COMMUNICATION ERROR]' with USB memory on Konica Minolta bizhub 215?
- J
  Justin DeanSep 1, 2025
  If your Konica Minolta All in One Printer displays a '[COMMUNICATION ERROR]' with the USB memory, it means the printer is having trouble communicating with the USB drive. Check that the USB memory is connected correctly.
C
Caleb RobinsonAug 30, 2025
What does '[USB Dev.Not support]' mean on Konica Minolta All in One Printer?
- W
  William LaraAug 30, 2025
  The '[USB Dev.Not support]' message on your Konica Minolta All in One Printer indicates that you're using either a non-USB memory stick or a write-protected USB memory stick. Use a writable USB memory stick to resolve this.
M
Michael Park DDSAug 29, 2025
What if transmission is enabled on Konica Minolta bizhub 215 All in One Printer, but no images are output?
- S
  Sarah GarciaAug 29, 2025
  If transmission is enabled on your Konica Minolta All in One Printer but no images are output at the destination, it could be due to the destination terminal lacking the processing capacity for the transmitted images. Configure the size, image quality, and compression coding method settings supported by the destination terminal, and then send the data again.
M
Matthew SheppardAug 28, 2025
How to fix 'ADF (Duplex) No Paper' error on Konica Minolta bizhub 215?
- R
  Ryan DillonAug 28, 2025
  If your Konica Minolta All in One Printer shows the error 'ADF (Duplex) No Paper', it means the original document is not set on the ADF. Simply set the original on the ADF to resolve this.
T
Tara MartinAug 27, 2025
What does '[USB MEMORY FULL]' mean on my Konica Minolta bizhub 215 All in One Printer?
- D
  Dr. Richard RayAug 27, 2025
  The '[USB MEMORY FULL]' message on your Konica Minolta All in One Printer indicates that the USB memory's capacity is less than the data size you're trying to scan. To resolve this, either increase the available space by deleting files on the USB memory, or use another USB memory stick with more available space.
K
kathyevansAug 27, 2025
What to do if my Konica Minolta bizhub 215 displays 'Scanner Busy'?
- R
  Rachel PerryAug 27, 2025
  If your Konica Minolta All in One Printer displays 'Scanner Busy', it's likely because a TWAIN scan and a copying job are running simultaneously, which can halt the scanning process. The solution is simple: wait until the copying or scanning process finishes.
D
David RoseAug 25, 2025
What causes 'Read Data Error' on Konica Minolta All in One Printer, and how can I fix it?
- D
  Danny GrahamAug 26, 2025
  A 'Read Data Error' on your Konica Minolta All in One Printer indicates an error occurred while scanning data. To resolve this: 1. Turn the machine OFF and check that the USB cable and network cable are connected correctly. 2. If the USB cable and network cable connections are found in order, turn the machine ON again. 3. If the problem persists, contact your service representative.
J
jessicamaciasAug 25, 2025
How to fix 'PC CONNECTION FAILED' on Konica Minolta bizhub 215?
- P
  Paige CarlsonAug 25, 2025
  If your Konica Minolta All in One Printer displays 'PC CONNECTION FAILED', with a 'Read Data Error' and '[Scanner not ready]' message, it could be due to several reasons: * The machine hasn't started. * A system crash occurred during transmission. * The USB or network cable isn't correctly connected. Here's how to troubleshoot: 1. Turn the machine OFF and ensure the USB and network cables are correctly connected. 2. If the connections are secure, turn the machine ON again. 3. If the problem persists, contact your service representative.

Konica Minolta bizhub 215 Specifications

General

Print Speed	21 ppm
Print Resolution	600 x 600 dpi
Paper Capacity	250 sheets
Max Paper Size	A3
Copy Speed	21 cpm
Connectivity	USB 2.0
Printing Technology	Laser
Copy Resolution	600 x 600 dpi
Scanning	Yes
Optical Scanning Resolution	600 x 600 dpi
Faxing	Optional
Multi-purpose Tray Capacity	100 sheets
Standard Output Capacity	250 sheets
Maximum Output Capacity	250 sheets
Internal Memory	128 MB
Dimensions	570 x 531 x 449 mm
Memory	128 MB
Time to First Page	8.5 seconds
Scan Type	Flatbed
Maximum Input Capacity	1350 sheets
Type	Monochrome
Functions	Print, Copy, Scan
Fax Transmission Speed	33.6 kbps
Network Connectivity	Optional