Konica Minolta Bizhub 222 User Manual (English)

Other manuals for Konica Minolta Bizhub 222

User Guide392 pages

Installation Manual36 pages

Questions and Answers:

B
Barbara JohnsonSep 9, 2025
How to fix error message displayed on Konica Minolta Bizhub 222 All in One Printer?
- J
  Joseph CabreraSep 9, 2025
  If your Konica Minolta All in One Printer displays an error message, and documents stored in the memory are waiting to be printed, print them. If functions that cannot be used together are selected, make copies using only one of the functions. If the paper size of the document cannot be detected, select the paper size of the document. If some malfunction occurred in the machine, inform your technical representative of the code displayed on the touch panel.
M
Matthew AguirreAug 25, 2025
What to do if the Konica Minolta All in One Printer displays a 'Busy line' error?
- K
  Kristen MckeeAug 26, 2025
  If your Konica Minolta All in One Printer shows 'Busy line' when trying to communicate with the Center, it means the line to the Center is currently occupied. The suggested solution is to try communicating with the Center again later.
D
Daniel TaylorAug 26, 2025
What to do if Konica Minolta Bizhub 222 All in One Printer shows 'No response'?
- P
  Penny OlsonAug 26, 2025
  If your Konica Minolta All in One Printer is showing 'No response' when trying to communicate with the Center, it indicates that the Center isn't responding. You can try the following: * Communicate with the Center again. * Check the communication environment of the Center side.
S
sheryllawsonAug 27, 2025
What to do if Konica Minolta All in One Printer shows "Malfunction detected"?
- M
  Morgan HaleAug 27, 2025
  If the message "Malfunction detected" appears on your Konica Minolta All in One Printer, follow these steps: 1. Write down the malfunction code (e.g., C-0001) from the call technical representative screen. 2. Turn the machine off using the [Power] (auxiliary power) key and the main power switch. 3. Unplug the machine. 4. Contact your technical representative and provide them with the malfunction code.
B
bjohnsSep 10, 2025
What to do if transmission is not possible on Konica Minolta All in One Printer?
- M
  Monica PetersonSep 10, 2025
  If transmission is not possible on your Konica Minolta All in One Printer, first, check the LED indicator on the hub and verify all connections. If the image data is too large, increase the timeout setting on the receiving end or decrease the image data size before re-transmitting. Ensure that the necessary network settings are correctly specified. Replace the LAN cable if it is damaged. If IP filtering is enabled, consult with the machine's administrator. For other causes, check the Job List screen for transmission error details and refer to the error codes table.
S
Shawn OsborneSep 13, 2025
How to clear a paper misfeed in the ADF of Konica Minolta All in One Printer?
- R
  Robert SmithSep 13, 2025
  To clear a paper misfeed in the ADF of your Konica Minolta All in One Printer: 1. Pull up the lever for the misfeed-clearing cover and open the cover. 2. Carefully remove any misfed paper. 3. Swing up the document guide lever. 4. Turn the dial to feed out any misfed documents. 5. Support the document feed tray with your right hand and carefully pull out any misfed documents. 6. Return the document guide lever to its original position, then close the misfeed-clearing cover.
W
Willie GardnerSep 4, 2025
What to do if Konica Minolta Bizhub 222 is showing error EAXXXX?
- S
  smithjoseSep 4, 2025
  If your Konica Minolta All in One Printer displays error EAXXXX, it indicates that the LAN cable is not connected, communication to the SMTP server failed, or transmission was attempted to an incorrect destination address. Check that the LAN cable is properly connected, that the SMTP server can communicate, that the network settings such as the subnet mask are correct, and that the destination e-mail address is correct.
C
Christopher CraigSep 5, 2025
How to fix Konica Minolta Bizhub 222 All in One Printer error EAX212?
- R
  Ryan ButlerSep 5, 2025
  If your Konica Minolta All in One Printer is displaying error EAX212, it means that SMTP authentication is requested. Enable the SMTP authentication settings to resolve this issue.
T
Timothy KirbyAug 31, 2025
What does it mean if Konica Minolta Bizhub 222 All in One Printer is showing error EF09CF?
- J
  Jason LynchAug 31, 2025
  If your Konica Minolta All in One Printer displays error EF09CF, it means that the protocol is incorrect. To resolve this, ask the administrator to deactivate the protocol usage restrictions, or look for other delivery methods.
Z
zduarteAug 30, 2025
What to do if Konica Minolta All in One Printer is showing error ED09C9?
- R
  Ryan SmithAug 30, 2025
  If your Konica Minolta All in One Printer displays error ED09C9, it indicates that the FTP server capacity is full. To resolve this, free up disk space on the FTP server.

Konica Minolta Bizhub 222 Specifications

General

Print Technology	Laser
Print Speed	22 ppm
Max Paper Size	A3
Resolution	600 x 600 dpi
Duplex Printing	Yes
Functions	Print, Copy, Scan
Copy Speed	22 cpm
Scan Resolution	600 x 600 dpi
Warm-up Time	15 seconds
Fax Speed	33.6 kbps
Connectivity	USB 2.0, Ethernet
Paper Capacity	250 sheets
Operating System Compatibility	Windows, Mac