Koso RS DYNO User Manual

INTRODUCTION
Thank you for purchasing KOSO RS DYNO digital LCM meter the meter is
displayed by lcm with led back light, before operating, please read the
instruction carefully and follow it to install the meter.
NOTICE
1.The lcd meter is apply for DC 12V.
2.For installation, please follow the steps described in manual. Any
damage caused by wrong installation shall be imputed to the users.
3.Don't break or modify the wire terminal. To avoid the short circuit, please
don't pull the wire when installing.
4.Do not disassemble or change any parts excluding the manual
description.
5.The interior examination or maintenance should be executed by our
professionals.
WARNING!
CAUTION!
You could get the installation details from the information behind the mark.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
Some processes must be followed to avoid the damage to the vehicle.
MARK MEANING:
Content
Accessory
1-1
Option accessory
1-2
2-1
Installation instructions
2-2
Wiring installation instructions
3-1
Basic function instruction
3-2
Standard screen function instruction
3-3
The button function instruction
3-4
The screen switch instruction
3-5
Main screen function switch instruction
3-6
Digital screen function switch instruction
3-7
The setting screen instruction
4
Function, setting instruction
4-1
Speed unit setting
4-2
Cycle/ piston setting
4-3
The temperature unit setting
4-4
Speeding warning light setting
1-1
4-5
Over RPM warning light setting
4-6
Over temperature (Water temperature)
warning light 1 setting
4-7
Over temperature (Oil temperature)
warning light 2 setting
4-8
Tire size adjustment/ sensor point setting
instruction
4-9
The clock setting instruction
4-10
Fuel sensor impedance & insufficient fuel
warning setting instruction
4-11
The target speed timer / target distance
timer setting
5-1
Target speed timer test
5-2
Target distance timer test
5-3
The top speed test
6
Trouble shooting
Guarantee & notice of products
7
Guaranty
8
2
5
8
1
4
7
10
3
6
9
11
12
TEMP 2
TEMP 1
Meter X 1
Main wiring X 1
PT1/8 water temp
sensor X 2
Connect
terminal X 7
D6 X 5L mm
magnet X 6
Digital speed
signal sensor X 1
M8/ S type speed
sensor bracket X 1
M5 X 5L hexago-
nal bolt X 2
RPM wire set
(Type A) X 1
RPM wire set
(Type B) X 1
M10/ S type speed
sensor bracket X 1
Temp sensor
wire set X 2
Accessory
1-1
Next page
Cortesia de www.motomarcadores.com
Cortesia de www.motomarcadores.com

Koso RS DYNO Specifications

General

Brand	Koso
Model	RS DYNO
Category	Measuring Instruments
Language	English

Summary

Introduction and Safety

Important Notices and Warnings

Key safety notices, warnings, and cautions for installation and operation.

Marking and Symbol Meanings

Explanation of symbols used in the manual to convey important information.

Accessory Components (1-1)

Meter and Wiring Accessories

Identification of meter, main wiring, RPM wire sets, and temp sensor wire sets.

Sensor and Mounting Accessories

Identification of temperature sensors, speed sensors, magnets, and brackets.

Optional Accessories (1-2)

Tools and Additional Components

List of optional tools like spanners and additional components like disc magnet screws.

Sensors and Adapters

Identification of optional sensors and adapters for temperature and speed.

Wiring Installation Instructions (2-1)

Connecting Meter and Sensors

Diagram and explanation for connecting meter wiring to vehicle electrical system and sensors.

Installation Instructions (2-2)

Motorcycle/Scooter Installation

Step-by-step guide for installing meter bracket and sensors on motorcycles/scooters.

ATV Speed Sensor Installation

Specific instructions for installing speed sensor bracket on ATVs.

Function Overview (3-1)

Speedometer, Indicators, and Warnings

Explanation of speedometer, indicator lights, and warning functions.

Other Displays: Temp, Fuel, Voltage, Odo, Trip, Clock

Details on temperature, fuel, voltage, odometer, trip meter, and clock displays.

Standard Screen Functionality (3-2)

Standard Screen Layout and Readings

Overview of the standard display screen, including indicators and readings.

Button Functionality (3-3)

Exit and Enter Button Operations

How to use the Exit and Enter buttons for navigation and confirmation.

Up/Down Button Operations

How to use Up and Down buttons for selection and value adjustment.

Screen Switching (3-4)

Navigating Between Main Screens

Instructions on how to switch between main, digital, and power test screens.

Main Screen Switching (3-5)

Toggling Fuel and Temperature Displays

How to switch between fuel and oil/water temperature displays on the main screen.

Toggling Odo, Trip, and Clock Displays

How to switch between odometer, trip meter, and clock displays on the main screen.

Digital Screen Switching (3-6)

Digital Display Information Toggles

How to switch between fuel, temperature, odometer, and trip meter on the digital screen.

Setting Screen Navigation (3-7)

Selecting Setting Screens

How to select and move between different setting screens using Up/Down buttons.

General Settings Configuration (4)

Speed, Warning, and Sensor Settings

Settings for speed unit, warning lights, tire size, and sensor points.

Clock and Fuel Settings

Settings for clock time and fuel sensor impedance/warning.

Speed Unit Setting (4-1)

Setting Speed Units (km/h or MPH)

Procedure to set the speed unit to either kilometers per hour or miles per hour.

Cycle/Piston Setting (4-2)

Setting Engine Strokes and Pistons

Procedure to set the engine's stroke count and piston configuration.

Setting Tachometer Signal Impulse

Procedure to set the signal impulse for the tachometer (low/high).

Temperature Unit Setting (4-3)

Setting Temperature Units (°C or °F)

Procedure to set the temperature display unit to Celsius or Fahrenheit.

Speeding Warning Light Setting (4-4)

Setting Speeding Warning Threshold

Procedure to set the speed at which the speeding warning light activates.

Over RPM Warning Light Setting (4-5)

Setting Over RPM Warning Threshold

Procedure to set the RPM level for the over-RPM warning light.

Water Temperature Warning Light Setting (4-6)

Setting Water Temperature Warning

Procedure to set the water temperature threshold for the warning light.

Oil Temperature Warning Light Setting (4-7)

Setting Oil Temperature Warning

Procedure to set the oil temperature threshold for the warning light.

Tire Size and Sensor Point Setting (4-8)

Setting Tire Circumference

Procedure to input the tire circumference for accurate speed readings.

Setting Sensor Points

Procedure to set the number of sensor points for speed detection.

Clock Setting Instruction (4-9)

Setting the Clock Time

Procedure to set the current time for the meter's clock display.

Fuel Sensor Settings (4-10)

Setting Fuel Sensor Impedance

Procedure to set the fuel sensor impedance value (e.g., 100 Ω, 510 Ω).

Setting Insufficient Fuel Warning

Procedure to set the fuel level threshold for the insufficient fuel warning.

Target Timer Settings (4-11)

Setting Target Speed Timer

Procedure to set the target speed for timing acceleration tests.

Setting Target Distance Timer

Procedure to set the target distance for timing acceleration tests.

Power Target Speed Timer Test (5-1)

Performing Target Speed Test

Instructions for conducting and viewing target speed test results.

Record Management for Speed Test

How to save new records or clear existing ones for the speed timer test.

Power Target Distance Timer Test (5-2)

Performing Target Distance Test

Instructions for conducting and viewing target distance test results.

Record Management for Distance Test

How to save new distance records or delete existing ones.

Power Target Distance Timer Test (5-2) - Record Handling

Saving Target Distance Records

Procedure to save a new target distance test record, replacing the previous one.

Deleting Target Distance Records

Procedure to delete the current record and return to the previous one.

Power Top Speed Test (5-3)

Performing Top Speed Test

Instructions for conducting and viewing the top speed test results.

Record Management for Top Speed Test

How to save new top speed records or delete existing ones.

Troubleshooting Guide (6)

Common Display and Sensor Issues

Troubleshooting for 'No display', 'Incorrect date', speed, tachometer, and fuel gauge problems.

Wiring and Power Issues

Troubleshooting for wiring connectivity, power supply, and spark plug related issues.

Guarantee and Product Notices (7)

Guarantee Rules and Conditions

Details of the product guarantee, including covered issues and exclusions.

Contact and Support Information

Information on how to contact for repairs or support if problems persist.