wh076ba01a(P3-1)
2-1
Wiring Installation Instructions
Green
-
Fuel
light
(-)
Installation instruction
2-2
1. M5X15 screw X2
(
Accessory 11
)
2. Meter bracket for handle bar
(
Accessory 9
)
3. Fix the bracket on handle bar
4. Meter bracket clip
(
Accessory 9
)
5. M4X12Lmm Screw X2 (Accessory 10)
6. M5 washer X2
(
Accessory 12
)
7. Meter fixed board
(
Accessory 9
)
8. Meter
(
Accessory 1
)
Follow this procedure for proper installation.
Special instruction for meter fit board.
A. Push meter bracket
clip up to lock meter
fix board (with meter)
on bracket.
B. Push meter bracket
clip down to release meter
fix board (with meter)
on bracket.
When using the eletronic speed sensor(Hall Sensor), the meter must connect with DC 12V battery instead of using inner battery from the meter.
When using Reed Sensor, the meter could function normally when using only the inner battery.
MOTO / SCOOTER
S type speed sensor bracket instruction
Loose the screw on the caliper.
Install the S type bracket on the caliper.
Adjusting the distance between the sensor
and screw to get the best speed signal.
Please make sure the distance is under 2 mm
to get the best signal.
Please adjust the bracket to the proper angle
and then screw it up.Please make sure the
disc screw could pass the hole on the bracket
for you to install the sensor into the same hole
for catching the speed signal.
Install the speed sensor(Accesory 3).
2 mm
Passive speed sensor
(
Accessory 3
)
Meter (Accessory 1)
Main wiring harness
(Accessory 2)
Blue-R turn signal light (+12V)
Purple
-
Engine light
(-)
Yellow
-
High beam light (
+12V)
Black / Ground wire connect to
the negative pole of the battery.
Mid-way connect
Red / Postive pole
(Connect to the battery DC 12V)
Gray-Motor oil light (-)
White-Neutral light (-)
Reed Sensor
(Option accessory 1)
Or
Yellow-white
-
Temperature
light
(-)
Orange-L turn signal light (+12V)
INSTALLATION
●
Thank you for purchasing the our product. Before installing, please read the instruction carefully and keep it for future reference.
Attention!
PRESS THE
BUTTON
ONCE
PRESS THE
BUTTON 3
SECONDS
FLASH LIGHT ON
● For installation, please follow the steps described in manual. Any damage caused by wrong installation shall be imputed to the users.
● Don't break or modify the wire. To avoid the short circuit, please don't pull the wire when installing.
● Do not disassemble or change any parts excluding the manual description.
● The interior examination or maintenance should be executed by our professionals.
◎ MARK MEANING:
Some processes must be followed to avoid the damage to the vehicle.
Some processes must be followed to avoid the affection caused by wrong installation.
Some processes must be followed to avoid damages to yourself or the public.
WARNING!
CAUTION!
NOTE
You could get the installation details from the information behind the mark.
Accessories1-1
Option accessory1-2
1
Meter X1
2
Main wiring harness X1
4
M8 / S type speed
sensor bracket X1
5
M10 / S type speed
sensor bracket X1
8
D6xH5 mm magnet x6
3
Passive speed sensor X1
6
M5x5xP0.8
Hexagon screw X2
9
Meter bracket X1
7
2.5 mm Allen key X1
1
Reed Sensor
12
M5 washer X2
13
4.0 mm Allen key X1
10
M4X12Lmm Screw X2
11
M5X15 screw X2
NOTE
Contact your local distributor, if the items received in the box are not the same as the items listed above.
NOTE
Some optional accessories may not be sold in your area. For more details, please contact your local distributor.
NOTE
Adjust the meter to the proper viewing angle
before tightening the Allen screw.
7.
8.
5.
6.
6.
5.
2.
3.
1.
1.
4.
To Next Page
Need help?
General
