Need help?Do you have a question about the Krone EasyCut B 870 CR and is the answer not in the manual?
General| Working width | 8.70 m |
|---|---|
| Transport width | 3.00 m |
| Transport height | 4.00 m |
| Number of Rotors | 2 |
| Overlap | 40 cm |
Manufacturer's declaration of compliance with EU directives.
Specifies the series of disc mowers for which these instructions are valid.
Explains the meaning of symbols used for safety instructions.
Details the different hazard warning levels: Danger, Warning, Caution.
Defines the intended application of the disc mower.
Specifies the correct and incorrect uses of the machine.
Information on factors affecting the machine's lifespan and maintenance.
General safety rules and regulations for operating the machine.
Safety precautions when attaching implements to the tractor.
Safety guidelines for operating the Power Take-Off shaft.
Safety precautions related to the machine's hydraulic system.
General safety rules for performing maintenance tasks.
Warning against unauthorized modifications and use of non-original parts.
Prohibits operating the machine outside its intended use or exceeding limits.
Safety instructions for working near overhead power lines.
Diagram and identification of major components of the machine.
Information on the machine's identification plate and its importance.
Details needed for contacting the manufacturer or ordering parts.
General information about safety labels on the machine.
Illustrations showing the location of safety stickers on the machine.
Specifications including dimensions, tractor requirements, and equipment.
Information on filling quantities and lubrication designations for gearboxes.
Reference to assembly instructions for initial setup of the machine.
Critical safety warnings before starting machine operations.
Procedure for connecting the machine to the tractor's hitch system.
Instructions for adjusting the length of the PTO shaft.
Procedure to check and vent the cross conveyor belts.
Steps for attaching the machine to the tractor's three-point hitch.
Safety and connection procedures for the hydraulic system.
Procedure for connecting the electrical controls and power supply.
Safety warnings and connection instructions for the lighting system.
Safety instructions and steps for installing the PTO shaft.
Instructions for connecting intermediate PTO shafts.
Procedure to move the parking supports to the transport position.
Steps to safely fold the machine for transport.
Pre-operation checks and safety warnings before mowing.
Detailed steps and settings for mowing operations.
Instructions for lowering mowing units into working position.
Instructions for operating the cross conveyor system.
Ensuring parking supports are correctly positioned for travel.
Step-by-step procedure for safely detaching the machine.
Guidelines for parking the machine, especially with folded units.
Procedure for adjusting the cutting height using the top link.
Instructions for adjusting the outer and inner guards.
Information on setting the pole protection mechanism for obstacle protection.
Procedure to set the tedder speed via the gearbox.
How to adjust the conditioner plate to change conditioning degree.
Procedure for adjusting the locking mechanism for side panels.
How to adjust the distance between the conditioner rollers.
Steps for setting the tension and alignment of the conveyor belt.
Procedure for adjusting the position of the cross conveyor.
Instructions for repairing a bent bar on the cross conveyor.
Safety precautions for performing a test run after maintenance.
Warning about using non-approved spare parts and the importance of original parts.
Schedule of maintenance tasks and their recommended intervals.
Specifications for tightening torques of various screw types.
Maintenance and function of the rotary hub with shear fuse.
Procedures for checking and changing oil in the main gearbox.
Procedures for checking and changing oil in the mower drive gearbox.
Procedures for checking and changing oil in the angular gearbox (top part).
Procedures for checking and changing oil in the angular gearbox (bottom part).
Procedures for checking and changing oil in the top roller drive gearbox.
Instructions for checking and changing oil in the cutter bar.
Instructions for checking cutter blades and their holders for wear and damage.
Detailed procedures for changing blades on cutting discs.
Procedure for replacing worn linings on the cutter bar.
Information regarding the machine's hydraulic oil tank and its function.
Instructions for replacing the hydraulic oil filter.
Safety warnings relevant to lubrication procedures.
Lubrication intervals for the PTO shaft.
Diagrams indicating lubrication points and intervals for the machine.
Instructions for cleaning the cross conveyor belts, with safety precautions.
Critical safety warnings before preparing the machine for a new season.
Safety and procedure for conducting a test run before the new season.
Information and procedure for venting the friction clutch.
General safety warnings applicable to special equipment.
Procedure for adjusting the skids to increase cutting height.
Guidelines for proper disposal of machine components and fluids.
Reference to the electrical circuit diagram for the machine.
To Next Page