Need help?Do you have a question about the Krone EasyCut F 360 CV and is the answer not in the manual?
General| Working width | 3.60 m |
|---|---|
| Transport width | 3.00 m |
| Number of discs | 8 |
| CV conditioner | Yes |
| Cutting System | Mower with cutterbar |
States which models the instructions apply to.
Explains how warning notes are presented and used.
Explains different hazard warning symbols and their meanings.
Describes the intended use of the disc mower.
Specifies the machine's intended use in agricultural work.
Information on the expected service life and factors affecting it.
Comprehensive safety guidelines and accident prevention rules for safe operation.
Provides a labeled diagram identifying key components of the machine.
Explains the information found on the machine's identification plate.
Lists data needed for inquiries and spare parts orders.
Provides contact details for the manufacturer.
Introduces safety devices and warning pictograms on the machine.
How to order replacement safety and information labels.
Instructions for applying safety and information labels.
Shows the locations of various safety stickers on the machine.
General information on technical data accuracy and design changes.
Details on filling quantities, lubrication, and disposal of consumables.
Critical safety warnings before commissioning the machine.
Instructions for initial assembly and installation of the machine.
Guidance on how to adapt the machine to the tractor.
Step-by-step guide for attaching the machine to the tractor.
Details on connecting the machine to the tractor's three-point hitch.
Instructions for adjusting or mounting lower suspension arm adapters.
Safety and adjustment procedures for the PTO shaft.
Steps for adjusting the length of the PTO shaft.
Steps to prepare the front-mounted disc mower before connection.
Guide to installing the PTO shaft on the front mower.
Steps to prepare the tractor before connecting the machine.
Instructions for installing the PTO shaft.
How to mount and adjust the relief springs for ground pressure.
Specific instructions for adjusting relief springs on the pushed design.
Procedure to check and adjust the spring retaining chain.
Specific instructions for checking the retaining chain on trailed designs.
How to tension the guard cloth before each use.
Steps for connecting the machine's lighting system.
Safety instructions and procedures for connecting hydraulic lines.
Critical safety warnings for hydraulic system connections.
Step-by-step guide for connecting hydraulic lines.
Performing a trial run after initial setup.
Verifying the correct mounting and alignment of the machine.
Safety warnings and checks for the lighting system during transport.
Checking the clamp and buffer for tight fit before transport.
How to move guards into transport position for safe travel.
Instructions for using and securing the parking support.
Safety precautions and checks before starting mowing operations.
How to tension the guard cloth before each use.
Steps to move the guards into their working position.
Procedures for safely detaching the machine from the tractor.
How to safely remove retaining chains.
How to adjust the compensation springs for ground pressure.
Specific instructions for adjusting compensation springs on the pushed design.
Specific instructions for adjusting compensation springs on the trailed design.
How to adjust the cutting height of the mower.
Adjusting cutting height using the telescopic upper suspension arm.
How to set the speed of the conditioner for optimal performance.
Steps for changing the pulley to adjust conditioner speed.
Instructions for replacing pulleys on the drive belt.
Procedure for tensioning the belt drive.
How to adjust the conditioner plate for different crop conditions.
Adjusting the conditioner plate for swathing.
Instructions for setting up the machine for wide spreading.
How to adjust the distance between the rollers.
Critical safety warnings before performing maintenance tasks.
Performing a test run after maintenance or repair.
Guidelines for using genuine KRONE spare parts.
A table outlining maintenance tasks and their intervals.
Torque specifications for various screws and nuts.
Torque specifications for metric thread screws with control thread.
Torque specifications for metric thread screws with fine thread.
Torque specifications for specific screw types.
Specifications for non-standard tightening torques.
Information on the intermediate PTO shaft and friction clutch.
Details on the rotary hub and shear fuse mechanism.
Procedures to follow after the shear pin has been activated.
Details oil level check and oil change for the input gearbox.
Details oil level check and oil change for the angular gearbox.
Oil level check and change for the top part of the angular gearbox.
Oil level check and change for the bottom part of the angular gearbox.
Details oil level check and oil change for the top roller drive gearbox.
Explains how to tension the belt drive.
Details oil level check and oil change procedures for the cutter bar.
Instructions on how to align the cutter bar using a spirit level.
How to check cutter blades and their holders for wear and damage.
Information on cutter blade wear and replacement criteria.
Instructions for connecting blades using screws and checking bolt material.
Procedures for using the quick-fit blade device.
How to periodically inspect leaf springs for damage.
How to inspect cutting discs and blade drums for damages.
Information on the wear limit for cutting discs and blade drums.
Safety precautions and procedures for changing blades on cutting discs.
Detailed steps for blade replacement using screw connections.
Steps for using the blade quick-fit system.
Instructions for replacing worn linings on the cutter bar.
Critical safety warnings before performing lubrication tasks.
Lubrication points and intervals for the drive shaft.
Lubrication intervals for the intermediate PTO shaft.
Visual guide to lubrication points and intervals for various components.
Critical safety warnings before preparing the machine for the new season.
How to perform a test run after seasonal preparation.
Information and procedures for the friction clutch.
Critical safety warnings related to special equipment.
How to adjust skids to increase cutting height.
Guidelines for proper disposal of machine components and materials.
To Next Page
