What to do if my KStar UPS has abnormal backup time?
If your KStar UPS has an abnormal backup time, it may be because the battery is not fully charged or the battery is bad. To address this, charge the battery for 8 hours when AC is normal, then test the backup time again.
What to do if my KStar 10kVA buzzer beeps twice every second and LCD shows “output overload”?
If your KStar UPS is beeping twice every second and the LCD displays “output overload”, it means the UPS is overloaded. To resolve this, disconnect some of the connected devices to reduce the load.
Why KStar 10kVA UPS doesn’t start after pressing On button?
If your KStar UPS doesn't start after pressing the On button, it could be due to two reasons: either the On button wasn't pressed long enough, or the UPS is overloaded. To fix this, press and hold the On button for one second. If that doesn't work, disconnect all loads and try restarting the UPS.
What to do if my KStar UPS shows fault indicator on and the LCD shows “battery fault”?
If the fault indicator is on and the LCD shows “battery fault” on your KStar UPS, it could be due to several reasons: * The battery circuit breaker might be off or have a poor connection. * The battery connection might be reversed. To solve this, switch on the breaker and check the battery connections. Also, verify the battery polarity.
What to do if my KStar 10kVA UPS has long beeps and fault indicator on, the LCD shows over-temperature?
If your KStar UPS is emitting long beeps, the fault indicator is on, and the LCD shows “over-temperature”, it indicates that the UPS is overheating. Check if there is wind blowing out from fans. Move any objects away from the UPS to improve ventilation. Wait until the UPS becomes cool, and then restart it.
What to do if my KStar 10kVA UPS has AC normal but AC indicator off, the UPS is in battery mode?
If the AC power is normal but the AC indicator is off, and the KStar UPS is running in battery mode, it could be due to: * The input circuit breaker being off. * An input power connection problem. To resolve this, switch on the input breaker and check the power connection, redoing it if necessary.
What to do if my KStar UPS has long beeps and fault indicator on, the LCD shows “output short circuit ”?
If your KStar UPS is emitting long beeps, the fault indicator is on, and the LCD shows “output short circuit”, it means there is a short circuit in the output. You should eliminate the short circuit and then restart the UPS.
What to do if my KStar 10kVA UPS AC indicator is blinking?
If the AC indicator on your KStar UPS is blinking, it indicates that the input AC power is beyond the normal range. Pay attention to the backup time if the UPS is in battery mode.
What to do if my KStar UPS has abnormal sound or smell?
If you notice an abnormal sound or smell coming from your KStar UPS, shut it down immediately.
What to do if my KStar UPS has no alarm but no output?
If your KStar UPS has no alarm but no output, it indicates an output connection problem. Check the connection and re-do it.
Specific actions prohibited to prevent electric shock and ensure warranty validity.
Important safety precautions for operating and handling the UPS unit.
Describes the suitable uses and environments for the UPS system.
Outlines the available models and configurations of the UPS system.
Illustrates the internal functional blocks and signal flow of the UPS.
Highlights the key technical characteristics and advanced capabilities of the UPS.
Provides a general description and visual representation of the UPS unit.
Shows a visual representation of the complete UPS unit.
Details how to operate and navigate the UPS using its LCD control panel.
Explains the different interfaces and information shown on the UPS LCD screen.
Lists and explains warning messages displayed by the UPS system.
Steps to verify the UPS unit and accessories upon receiving it.
Comprehensive guide on how to physically install the UPS unit and its components.
Important considerations and precautions before and during UPS installation.
Specific steps for installing external battery connections for extended models.
Instructions for connecting multiple UPS units in a parallel configuration.
Explains the different operational states of the UPS (AC, Bypass, Battery, ECO).
Describes operation when AC power is normal and supplied to the load.
Details operation when UPS is in bypass, typically due to overload or fault.
Explains operation when the UPS supplies power from its batteries.
Describes the energy-saving Economy mode of operation.
Step-by-step guide for powering on the UPS system safely.
How to configure various operational parameters via the LCD interface.
Procedures for starting the UPS under different conditions, including AC availability.
Instructions for performing a manual test of the UPS battery performance.
Steps for safely shutting down the UPS inverter.
Procedure for completely powering off the UPS unit.
How the UPS switches between different operating modes automatically.
Explains the UPS's behavior when the load exceeds its capacity.
Describes the transition to battery power when AC input fails.
How the UPS enters bypass mode due to high internal temperatures.
Procedures for handling and recovering from an output short circuit condition.
Guidance on monitoring UPS status using provided software.
Detailed guide for navigating and using the UPS's LCD menu system.
How to navigate between main menu options on the LCD.
How to navigate and select options within submenus on the LCD.
Explains the display logic and priority of information on the LCD screen.
Guidelines for checking and maintaining the UPS cooling fans.
Procedures for maintaining the UPS battery for optimal performance and lifespan.
Recommendations for performing visual inspections of the UPS.
Methods for checking the current operational status and indicators of the UPS.
Periodic checks to ensure all UPS functions are operating correctly.
Specifies the pinout and function of the USB connector on the UPS.
Lists and explains various status codes indicating the UPS's current operating state.
Provides a detailed breakdown of status messages and their corresponding indicators.
Lists and explains critical alarm codes indicating potential faults or issues.
Lists and explains additional alarm codes for system faults and warnings.
General| Apparent Power | 10kVA |
|---|---|
| Output Voltage | 220/230/240VAC |
| Efficiency | >90% |
| Operating Temperature | 0-40°C |
| Capacity | 8kW |
| Output Frequency | 50/60Hz |
| Battery Type | Sealed Lead-Acid (SLA) |
To Next Page
