KTM 65 sx 2011 - Technical Data - Fork

91 pages

Save Page as PDF

To Next Page

To Previous Page

TECHNICAL DATA - CARBURETOR 77

POS Needle position from above

MJ Main jet

The carburetor configuration depends on the ambient and operating conditions.

Info

Does not apply to sand surfaces!

Additional information can be obtained from your authorized KTM workshop.

Main Page

Table of Contents4
Means of Representation6
Important Information7
View of Vehicle9
- View of the Vehicle from the Left Front (Example)9
- View of the Vehicle from the Right Rear (Example)10
Serial Numbers11
- Chassis Number11
- Engine Number11
- Shock Absorber Part Number11
Controls12
- Clutch Lever12
- Hand Brake Lever12
- Throttle Grip12
- Short Circuit Button12
- Opening Filler Cap12
- Closing Filler Cap13
- Fuel Tap13
- Choke13
- Kickstarter13
- Shift Lever13
- Foot Brake Lever14
- Plug-In Stand14
Putting into Operation15
- Advice on First Use15
- Running in the Engine16
Riding Instructions17
- Checks and Maintenance Measures When Preparing for Use17
- Starting17
- Starting up18
- Shifting, Riding18
- Braking18
- Stopping, Parking19
- Refueling19
Service Schedule21
Tuning the Chassis23
- Adjusting the Compression Damping of the Fork23
- Adjusting the Rebound Damping of the Fork23
- Adjusting the Compression Damping of the Shock23
- Absorber23
- Adjusting the Rebound Damping of the Shock Absorber24
- Measuring Rear Wheel Sag Unloaded24
- Checking the Static Sag of the Shock Absorber24
- Checking the Riding Sag of the Shock Absorber25
- Adjusting the Spring Preload of the Shock Absorber25
- Adjusting the Riding Sag26
- Handlebar Position26
- Adjusting Handlebar Position26
- Vehicle Level27
- Adjusting the Fork Overhang27
Maintenance Work on the Chassis29
- Raising the Motorcycle with a Lift Stand29
- Removing the Motorcycle from the Lift Stand29
- Bleeding Fork Legs29
- Cleaning the Dust Boots of the Fork Legs29
- Removing the Fork Legs30
- Installing the Fork Legs30
- Removing the Fork Protector31
- Installing the Fork Protector32
- Removing the Lower Triple Clamp32
- Installing the Lower Triple Clamp33
- Checking Play of Steering Head Bearing35
- Adjusting Play of Steering Head Bearing35
- Greasing the Steering Head Bearing35
- Removing the Shock Absorber36
- Installing Shock Absorber36
- Dismounting the Start Number Plate36
- Installing the Start Number Plate36
- Dismounting the Front Fender37
- Installing the Front Fender37
- Removing the Seat37
- Mounting the Seat37
- Removing the Air Filter38
- Installing the Air Filter38
- Cleaning Air Filter39
- Removing Main Silencer39
- Installing the Main Silencer39
- Changing the Glass Fiber Yarn Filling of the Main Silencer40
- Dismounting the Fuel Tank40
- Silencer X40
- Installing the Fuel Tank41
- Removing the Chain Guard42
- Installing the Chain Guard42
- Checking Chain Dirt43
- Cleaning the Chain43
- Checking the Chain Tension43
- Adjusting the Chain Tension44
- Checking the Chain, Rear Sprocket, Engine Sprocket and Chain Guide45
- Checking the Chain Tension - Installing Rear Wheel46
- Adjusting Chain Tension - after Checking47
- Adjusting Chain Tension - Installing Rear Wheel47
- Adjusting the Chain Guide47
- Checking the Throttle Cable Routing48
- Adjusting Basic Position of Clutch Lever48
- Checking the Fluid Level of Hydraulic Clutch48
- Changing the Hydraulic Clutch Fluid48
Brakes50
- Checking Free Travel of Hand Brake Lever50
- Adjusting the Basic Position of the Hand Brake Lever50
- Checking Brake Discs50
- Checking the Front Brake Fluid Level51
- Adding Front Brake Fluid51
- Checking the Front Brake Linings52
- Removing Front Brake Linings52
- Installing the Front Brake Linings53
- Changing the Front Brake Linings54
- Checking the Free Travel of the Foot Brake Lever54
- Adjusting the Free Travel of the Foot Brake Lever55
- Adjusting the Basic Position of the Foot Brake Lever55
- Checking Rear Brake Fluid Level56
- Adding Rear Brake Fluid56
- Checking the Rear Brake Linings57
- Removing Rear Brake Linings57
- Installing the Rear Brake Linings58
- Changing the Rear Brake Linings58
Wheels, Tires60
- Removing the Front Wheel60
- Installing the Front Wheel60
- Removing the Rear Wheel61
- Installing the Rear Wheel61
- Checking the Tire Condition62
- Checking Tire Air Pressure62
- Checking Spoke Tension62
Cooling System64
- Checking the Antifreeze and Coolant Level64
- Checking the Coolant Level65
- Draining the Coolant65
- Refilling Coolant66
Tuning the Engine67
- Checking the Play in the Throttle Cable67
- Adjusting the Play in the Throttle Cable X67
- Carburetor - Idle67
- Carburetor - Adjusting the Idle Speed67
- Emptying the Carburetor Float Chamber68
Maintenance Work on the Engine69
- Checking the Gear Oil Level69
- Changing the Gear Oil69
- Draining the Gear Oil69
- Filling up with Gear Oil70
- Adding Gear Oil70
Cleaning, Care72
- Cleaning Motorcycle72
Storage73
- Putting into Operation after Storage73
Troubleshooting74
Technical Data - Engine76
Technical Data - Engine Tightening Torques77
Technical Data - Carburetor78
- Basic Setting78
- Carburetor Configuration78
Technical Data - Chassis80
Technical Data - Fork81
Technical Data - Shock Absorber82
Technical Data - Tightening Torques for Chassis83
Substances84
Auxiliary Substances86
Standards88
Index89

KTM 65 sx 2011 - Technical Data - Fork

Table of Contents

Related product manuals