How to prevent soil build up in front of the cutterbar on my KUHN FC4060TCR?
Soil build-up in front of the cutterbar on your KUHN Lawn Mower can be caused by too much cutterbar down pressure. Adjust the mowing unit ground pressure. It can also occur in very wet working conditions, so adjust the mowing unit ground pressure and the cutting height.
Why is my KUHN Lawn Mower leaving uneven stubble?
Uneven stubble on your KUHN Lawn Mower can occur due to dull or broken knives, so replace them. Ensure knives are installed correctly, with the arrow on the knife's upper face pointing in the disc's rotation direction. Reduce ground speed if it's excessive. Adjust the cutting height and mowing unit ground pressure. If dealing with tangled or down crops, reduce the cutting height and increase the mowing unit ground pressure.
How to fix badly shaped windrows with KUHN Lawn Mower?
Badly shaped windrows on your KUHN Lawn Mower can be caused by a PTO speed that is too low. Check the PTO speed, referring to the decal on the machine. Also, the swath shields may be incorrectly adjusted; in this case, adjust both swath shields.
What to do if KUHN FC4060TCR Lawn Mower roller is clogging?
Roller clogging in your KUHN Lawn Mower can be caused by a PTO speed that is too low. Check the PTO speed, referring to the decal fitted on the machine. Check the play between rollers and adjust the clearance depending on the crop. If the swath shields are too closed, open them.
Why does my KUHN FC4060TCR require too much pull power?
If your KUHN Lawn Mower requires too much pull power, it could be due to too much cutterbar down pressure. Adjust the mowing unit ground pressure to resolve this issue.
How to stop considerable vibrations in KUHN FC4060TCR Lawn Mower?
Considerable vibrations in your KUHN Lawn Mower can be due to issues with the roller parallelism and gap. Adjust the parallelism and gap between the rollers.
Diagram showing the front perspective of the mower conditioner, detailing its components.
Diagram illustrating the rear perspective of the mower conditioner, identifying key parts.
Details on the model identification plate, listing various machine identifiers and their meanings.
List of optional equipment that can be fitted to the mower conditioner.
Explanation of warning symbols used throughout the operator's manual.
Essential safety rules and guidelines for operating and maintaining the mower conditioner.
Information on required road safety equipment and general recommendations for transport.
Identifies potential critical failures of the machine and their causes.
Detailed description and glossary of the mower conditioner's components and terminology.
Key technical data and dimensions for FC4060 and FC4460 models.
Specifies the necessary PTO shafts and other equipment for operating the machine.
Presents measured sound levels for the tractor and the tractor-machine assembly.
Identifies control elements and tools supplied with the machine for initial setup.
Step-by-step guide for coupling and uncoupling the mower conditioner to a tractor.
Instructions for correctly connecting the hydraulic hoses for machine operation.
Guidelines for correctly installing and checking the primary PTO shaft.
Details on how to place the machine in its correct transport configuration.
Ensuring compliance with highway codes and regulations for road transport.
Steps to transition the mower conditioner from transport to working configuration.
Guidance on making adjustments for optimal performance during operation.
Procedure for adjusting the ground pressure of the mowing unit for different conditions.
How to adjust the conditioning intensity based on crop type and moisture.
Instructions for adjusting swath width and setting up for wide spreading.
Procedures for safely parking the mower conditioner before disconnecting it.
Explanation of check chains for lift linkage stabilization and frame height.
Details on lifters that improve forage transport to the conditioner.
Instructions for adjusting the wide spreading system's fins and components.
Guide to adjusting skid shoes to achieve different mowing heights.
Schedule of maintenance intervals based on operating hours and time.
Steps for cleaning the machine to remove debris and prevent build-up.
Information on lubricating grease nipples and components with multi-purpose grease.
Detailed instructions for lubricating PTO shafts and universal joints.
Procedures for draining and refilling oil in the cutterbar and gearboxes.
Guidance on inspecting and replacing knives and their securing components.
Procedures for adjusting the ground pressure system's torsion bars.
Instructions for storing the machine at the end of the season and preparing it for the next.
Guidelines for safely disposing of or recycling machine components at end-of-life.
Diagnosing and resolving issues causing uneven stubble after mowing.
Identifying causes and solutions for roller clogging on the mower conditioner.
Troubleshooting excessive pull power requirements and related causes.
Details on the terms, conditions, and coverage of the limited warranty for the equipment.
Outlines customer responsibilities, including maintenance and claim procedures.
General| Brand | KUHN |
|---|---|
| Model | FC4060TCR |
| Category | Lawn Mower |
| Language | English |
To Next Page
