What to do if my KUPPET 1022101300 Ice Maker cycle is normal, but no ice cube is produced?
If your ice maker completes its cycle but produces no ice, the ambient temperature or the water temperature in the tank might be too high. Try moving the unit to a place where the temperature is lower than 32 degrees centigrade and use colder water.
Why is the “ICE-FULL” symbol on my KUPPET 1022101300?
The “ICE-FULL” symbol illuminates because the ice storage bin is full. Simply remove some ice cubes from the bin.
What to do if my KUPPET 1022101300 is making very thin ice cubes?
If your ice cubes are too thin, it could be due to a high ambient temperature. Try moving the unit to a cooler location or lengthening the ice-making cycle. Also, ensure proper air circulation by providing at least 20cm of free space around the back and front of the unit.
How to fix irregular ice cube shapes in my KUPPET 1022101300 Ice Maker?
Irregular ice cube shapes can be caused by poor water quality or a dirty water tank. Clean the water tank and replace the water. It could also be due to blocked holes on the water dividing pipe, so ensure all nine holes are unclogged by cleaning the water dividing pipe.
What to do if the whole symbol is always on in my KUPPET Ice Maker?
The continuous illumination of the symbol indicates a water supply issue. If using automatic water supply, check if the main water pressure is too low or the water supply hose is blocked. Increase the water pressure or clean the hose. If using manual water supply, ensure the water charging tank is filled to the MAX level. Also, check if the floating ball of the water level detecting switch is blocked and clean the water tank and the water level detecting switch. Make sure that the unit is placed on a level surface. Ensure that the water drain pipe is properly installed in the right side slot of the water tank.
Why is the transparency of the ice cube not very good in my KUPPET Ice Maker?
Poor ice cube transparency is often due to bad water quality. Use a water filter or water purifier to soften or filter the water before using it in the ice maker.
What to do if my KUPPET 1022101300 Ice Maker is making ice cubes that are too thick?
If the ice cubes are too thick, the ambient temperature might be too low. Try reducing the duration of each ice-making cycle.
What to do if the water pump works, but no water flows out from the water dividing pipe in my KUPPET 1022101300 Ice Maker?
If the water pump is functional but no water is dispensed from the dividing pipe, the small holes on the pipe are likely blocked. Clean these holes to restore water flow.
What to do if my KUPPET Ice Maker enters the ice-making process, but no water is flowing in the unit, and the whole symbol is on?
This issue may arise due to a lack of water in the charging tank, a water supply problem, or incorrect positioning of the water tank's silicone pipe. If using automatic water supply, check if the main water pressure is too low or the water supply hose is blocked. Increase the water pressure or clean the hose. If using manual water supply, ensure the water charging tank is filled to the MAX level. Ensure the silicone pipe is correctly clamped in the slot on the water tank side.
What to do if the water circulation pump doesn’t work in my KUPPET 1022101300?
If the water circulation pump isn’t working, there may be a foreign substance blocking the pump blade. Clean both the water tank and the water pump.
Explains safety alert symbols, DANGER, and WARNING meanings.
Covers safe usage, cord handling, power, ventilation, and environmental tips.
Details electrical safety, grounding, wire colors, and installation guidelines.
Provides physical dimensions and connection details of the ice maker.
Lists electrical ratings, ice making capacity, and refrigerant type.
Details the primary components and construction of the ice maker unit.
Identifies and describes parts related to the ice-making and water tank system.
Explains the functions of the control panel buttons and display indicators.
Step-by-step guide for removing and preparing the ice maker from packaging.
Specifies suitable locations and clearance for installing the ice maker.
Outlines necessary electrical setup and grounding for safe operation.
Details connecting the water supply hose to the unit for automatic operation.
Explains how to connect the water drainage pipe to the unit.
Describes connecting the water hose to the main water supply system.
Guides on choosing between automatic and manual water supply modes.
Visual explanation of ice making, harvest, and water supply symbols.
Details process steps, symbol meanings, temperature units, and thickness adjustment.
Explains the effect of water quality on ice cube quality.
How to start and stop the self-cleaning cycle.
Guides for setting and canceling delayed ON and OFF timers.
Controls for internal LED and description of normal operational sounds.
Explains error codes E1 and E2 for unit malfunctions.
Details how to drain water from different parts of the unit.
What not to do and how to clean the exterior.
Procedures for sanitizing the ice storage bin.
How to clean the water dividing pipe and evaporator.
Mixing cleaner and running the self-cleaning program.
Draining, rinsing, and repeating the cleaning process.
Recommended daily cleaning tasks for the ice maker.
Recommended cleaning tasks every two weeks.
Recommended cleaning tasks every six months.
Addresses problems related to no water in the unit.
Solutions for water flow issues and pump malfunctions.
Fixes for poor ice transparency or irregular ice cube shapes.
Solutions for thin ice cubes, thick ice cubes, or no ice production.
To Next Page
General