Kyocera FS-2020D Operation Guide

Using the Operation Panel 2-79
3 Once you enter the correct ID and password, the Admin (change)
screen appears. (E.g.: Where the administrator ID is 00000001)
Each time you press U or V, the following settings to be changed
appear in succession.
• Change ID
• Change Password
4 Press [OK] again. The administrator ID and password are
confirmed.
5 Press [MENU]. The display returns to Ready.
Change ID (Administrator ID change)
You can use this to change the administrator ID.
1 In step 3 in Password (Administrator Password input) above, press
U or V while the Admin (Change) screen is displayed until
>Change ID appears. (E.g.: Where the administrator ID is 001)
2 When you press [OK], a blinking cursor (_) appears.
3 Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the ID to be changed. Use Y and Z to move
the cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4 Press [OK]. A confirmation screen appears. (E.g.: Where the
administrator ID is changed to 002)
5 Press [OK]. The new administrator ID is confirmed.
6 Press [MENU]. The display returns to Ready.
Change Password (Administrator Password change)
You can use this to change the administrator password.
1 In step 3 in Password (Administrator Password input) above, press
U or V while the Admin (Change) screen is displayed until
>Change Password appears.
2 Press [OK]. A blinking cursor (_) appears.
3 Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the password to be changed. Use Y and Z to
move the cursor right and left. Enter a password consisting of
between 0 and 16 numbers.
4 Press [OK]. A confirmation screen appears. (E.g.: Where the
administrator password is changed to 010)
Note If a change is required, refer to the procedures in
Change ID (Administrator ID change) and Change
Password (Administrator Password change) below.
>Change ID
00000001
>Change ID
001
>Change ID
_
OK?
002
IMPORTANT The administrator password is not displayed.
>Change Password
****************
>Change Password
_
OK?
010

Kyocera FS-2020D Specifications

General

Color	No
Duplex printing	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	9 s
Print speed (black, normal quality, A4/US Letter)	35 ppm
Memory type	DDR2
Processor model	PowerPC 440
Maximum internal memory	1152 MB
Sound power level (standby)	29 dB
Sound pressure level (printing)	52 dB
Power supply type	220/240 V, 50/60 Hz
Capacity cartridge	12000 sheets
Power consumption (active)	560 W
Recommended monthly print volume	20000 pages
Maximum duty cycle	150.000 pages per month
Number of print cartridges	1
Total input capacity	500 sheets
Total output capacity	250 sheets
Maximum input capacity	1100 sheets
Maximum number of input trays	2
Multi-Purpose tray input capacity	100 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Plain paper, Recycled paper
Paper tray media weight	60 - 120 g/m²
Non-ISO print media sizes	Letter
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	60 - 220 g/m²
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	9.2 W
Power consumption (PowerSave)	5.7 W
Energy Star Typical Electricity Consumption (TEC)	2.6 kWh/week
Display	LCD
Certification	GS, TüV, CE
Standard interfaces	Parallel, USB 2.0
Optional connectivity	Ethernet, Wireless LAN
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Dimensions (WxDxH)	382 x 394 x 285 mm