Kyocera KM-C3225 - User Manual

Questions and Answers

K
Kristin FordAug 22, 2025
Why is Kyocera Software not discovering the printing system?
- S
  Samantha OsbornAug 22, 2025
  The printing system might be turned off, so turn it on and try again. It could also be removed from the network, so ensure it's connected. If the system is currently printing, wait until it's finished and then try searching again. It is also possible that the TCP/IP settings on your PC are not configured properly, in that case contact your network administrator. Depending on the network router configuration, a printing system may be undetectable. In some rare cases, heavy network traffic may prevent this application from detecting the printing systems, so try again later or contact your network administrator.
T
Tyler MaxwellAug 25, 2025
What to do if Kyocera Software application does not start?
- M
  Mariah LesterAug 25, 2025
  If the Kyocera Software application doesn't start, it could be due to several reasons. First, your PC might not meet the necessary system requirements; in this case, consider upgrading your PC. Another possibility is low memory; try closing any unnecessary applications. Also, ensure that you are not trying to run two instances of the application simultaneously, as this is not supported.
A
Andrew RamirezAug 26, 2025
Why does Kyocera Software fail to obtain account or printing system information?
- S
  Sarah RobertsAug 26, 2025
  The application might fail to obtain account or printing system information if the printing system is turned off; in this case, turn it on. Another reason could be that the printing system has been removed from the network; connect it to the network. Also, if the printing system is currently printing a document, wait until the operation is complete before trying again.
D
Debra ThompsonAug 28, 2025
How to fix Kyocera Printer Accessories if ejected copies are not flat?
- D
  Dawn WilliamsAug 28, 2025
  If ejected copies are not flat or stacked unevenly, turn over the paper in the cassette and reload it.
S
Sarah LewisAug 30, 2025
Why is my Kyocera KM-C3225 Printer Accessories frequently jamming in the conveyor?
- D
  david74Aug 30, 2025
  If frequent jamming occurs in the conveyor or internal tray, the paper may be excessively curled. Also, you can adjust using the pressure roller bottom adjuster knob (E1) and pressure roller top adjuster knob (E2).
B
Brandon DavenportSep 1, 2025
What to do if Kyocera KM-C3225 shows a paper jam in Tray A?
- T
  Tyler WilliamsSep 1, 2025
  If the illustration shown displays on the machine’s operation panel, indicating a paper jam in the conveyor section to Tray A, lift open Tray B and remove the jammed paper.
T
thomas61Sep 3, 2025
What to do if Kyocera Printer Accessories shows a paper jam in Tray B?
- C
  Christopher KingSep 3, 2025
  If the illustration shown displays on the machine’s operation panel, indicating a paper jam in the conveyor section to Tray B, remove any jammed paper from the ejection section.
V
Victor CohenSep 5, 2025
How to fix curled copies from Kyocera KM-C3225 Printer Accessories?
- W
  Walter GarzaSep 5, 2025
  If the copies ejected are curled, adjust using the pressure roller bottom adjuster knob (E1) and pressure roller top adjuster knob (E2).
D
davidhillSep 7, 2025
What to do if Kyocera Printer Accessories shows a paper jam in the Document Finisher?
- V
  Veronica SantosSep 7, 2025
  If the illustration shown displays on the machine’s operation panel, indicating a paper jam in the coupling section between the Document Finisher and the machine, push the finisher release lever while pulling the finisher out from the machine.
J
Jason KelleySep 9, 2025
What to do if Kyocera Printer Accessories shows a paper jam in Tray C?
- J
  Jacob BurgessSep 9, 2025
  If the illustration shown displays on the machine’s operation panel, indicating a paper jam in the conveyor section to Tray C, push the finisher release lever while pulling the finisher out from the machine.