Kyosho FW-05 S User Manual

Emphasizes that the RC model is not a toy and requires careful handling.

Recommends seeking advice from experienced modelers for first-time builders.

Instructs to assemble the kit in a place inaccessible to children due to small parts.

Advises caution and responsibility for the model's assembly and safe operation.

Specifies the need for a minimum 2-channel radio system with 2 servos for operation.

Details the requirement for AA-size batteries and a battery box for the radio system.

Lists essential fuel and starting tools, warning against using petrol or kerosene.

Lists necessary tools like screwdrivers, pliers, and knives for model assembly.

Identifies tools provided within the kit, such as hex wrenches and needle-nose pliers.

Outlines the procedure for setting up the radio transmitter and receiver before use.

Explains how to interpret symbols, diagrams, and part identification within the manual.

Describes common symbols used throughout the manual for clarity during assembly.

Provides a guide to identifying different types and sizes of screws and hardware.

Shows the layout of plastic parts on runner number 3 for identification.

Displays the arrangement of plastic parts found on runner number 4.

Illustrates the layout of plastic parts on runner number 6.

Shows the arrangement of plastic parts on runner number 7.

Highlights specific shaded parts on the runners that are not used in the assembly.

Details the parts required for assembling the front and rear gear differentials.

Explains the correct type and amount of silicone oil to use for front and rear differentials.

Lists all the components needed to assemble the 2-speed transmission system.

Provides step-by-step instructions for building the 2-speed transmission unit.

Details the brake shaft and piston parts required for assembly.

Guides the user through the process of assembling the brake mechanism.

Lists the parts needed to assemble the center gearbox.

Provides instructions for putting together the center gearbox unit.

Lists the parts required for assembling the steering mechanism.

Details the steps for mounting the steering servo.

Lists the parts used to connect the steering servo to the steering mechanism.

Provides instructions for assembling the various steering linkage parts.

Lists the components for the main steering assembly.

Guides the attachment of the steering assembly to the main chassis.

Lists all the parts needed to assemble the front gearbox.

Explains how to adjust the backlash in the front gearbox using shims.

Provides instructions for assembling the main housing of the front gearbox.

Lists parts for the left side of the front suspension assembly.

Lists parts for the right side of the front suspension assembly.

Details the steps for assembling the suspension arms.

Guides the attachment of the front suspension assembly to the main chassis.

Advises on trimming parts if the steering plate interferes with the front bulkhead.

Details the assembly of the front bulkhead and steering plate.

Instructs to tighten screws that were temporarily installed earlier.

Shows the installation of swing shafts and E-rings.

Guides the installation of O-rings and shafts within the suspension.

Lists the parts required for mounting the front bumper.

Provides instructions for attaching the bumper to the front bulkhead.

Lists all components needed for the rear gearbox assembly.

Explains how to adjust the backlash using shims in the rear gearbox.

Lists parts for the left side of the rear suspension assembly.

Lists parts for the right side of the rear suspension assembly.

Details the steps for assembling the rear suspension arms.

Guides the attachment of suspension components using specific holes.

Shows the installation of the swing shaft into the rear suspension.

Lists the screws used to mount the rear shock stay.

Provides instructions for attaching the rear shock stay to the chassis.

Details the installation of the swing shaft with screws.

Guides the attachment of the rear suspension assembly to the chassis.

Lists the screws required for mounting the rear body mounts.

Provides instructions for attaching the rear body mounts.

Lists the parts needed to assemble the rear stabilizer.

Details the steps for assembling the stabilizer links and ball ends.

Lists the screws for mounting the steering servo.

Explains how to set up the steering servo, including neutral position.

Lists the parts for mounting the steering and throttle servos.

Guides on adjusting servo mounting for specific dimensions.

Lists the screws used to mount the switch.

Provides instructions for attaching the switch unit to the chassis.

Lists the screws for mounting the radio box.

Guides on how to thread servo cords through the radio box.

Details connecting the receiver, antenna, and battery as per radio instructions.

Shows the installation of the body pin.

Lists the screws for mounting the radio plate.

Provides instructions for attaching the radio plate to the chassis.

Lists the parts for assembling the engine unit.

Provides step-by-step instructions for assembling the engine unit.

Lists the parts required for mounting the engine.

Guides the installation of the engine onto the chassis.

Details the screws and settings for engine mounting.

Explains how to adjust the gear mesh between the engine and gears.

Lists the parts for assembling the throttle linkage.

Guides the connection of the throttle linkage to the servo horn.

Explains how to adjust the throttle and brake linkages for proper operation.

Guides the installation and securing of the fuel tank and fuel tube.

Lists the parts for assembling the front shock absorbers.

Provides step-by-step instructions for assembling the front shock absorbers.

Details the assembly of the front shock absorber for the short configuration.

Explains how to fill the front shock absorbers with silicone oil.

Shows the installation of pillow balls on the front shock absorbers.

Guides the attachment of the front shock absorbers to the chassis.

Shows the installation of pillow balls on the rear shock absorbers.

Guides the attachment of the rear shock absorbers to the chassis.

Lists the parts for the air cleaner assembly.

Guides the attachment of the air cleaner to the engine.

Details how to cut tires and mount them onto the wheels.

Explains how to apply instant glue to secure tires to wheels.

Guides the installation of the front wheels onto the chassis.

Guides the installation of the rear wheels onto the chassis.

Lists the screws used for mounting the body shell.

Provides instructions for attaching the body shell to the chassis.

Stresses preparing the engine before adjusting shift timing.

Explains how to adjust shift timing by tightening/loosening screws.

Advises setting shift timing for optimal performance at 80% of maximum RPM.

Guides adjusting the left/right set screws to align with the stabilizer holder.

Explains how to adjust the down stop by rotating stabilizer cams.

Details the installation of the optional front one-way shaft.

Guides the installation of the optional carbon shock stay for the front.

Guides the installation of the optional carbon shock stay for the rear.

Lists places and situations where the model should not be operated due to safety risks.

Stresses checking radio battery levels to maintain control and prevent accidents.

Provides essential safety guidelines for handling flammable glow fuel.

Warns against putting fingers or objects into moving parts to prevent injury.

Detailed exploded view illustrating the arrangement of various model components.

Continues the detailed exploded view of model components.

Lists spare parts from VS001 to VS020 with their corresponding key numbers and quantities.

Lists spare parts from VS021 to VS058 with their corresponding key numbers and quantities.

Lists spare parts from VS101 to VSW052 with their corresponding key numbers and quantities.

Lists spare parts from ORG05 to VSW020 with their corresponding key numbers and quantities.

Lists spare parts from VSW021 to VSW052 with their corresponding key numbers and quantities.

Lists optional parts from 80161 to 96981 with their corresponding key numbers and quantities.

Lists various body shells with their part numbers and associated decals.

Lists pre-painted complete body shell sets available for the model.

Lists available glow fuel types with nitro percentages and quantities.

Lists available tires with 26mm width, specifying grip levels and sizes.

Lists available tires with 24mm width, specifying grip levels and sizes.

Lists available wheels with 26mm width, specifying spoke designs and colors.

Lists available wheels with 24mm width, specifying spoke designs and colors.

Lists available racing mold inner sponges in different sizes (H, M, S).

Lists various types and sizes of screws and nuts with their quantities.

Lists E-clips, washers, and other small fasteners with their specifications.

Lists silicone oils for shocks and differentials, categorized by viscosity and volume.