Land Pride RC2512 Series

Questions and Answers

J
James LopezJul 28, 2025
What to do if the blades lock up on my Land Pride Cutter?
- M
  melinda01Jul 28, 2025
  If the blades of your Land Pride Cutter lock up, use a pry bar or another tool to separate the cutting blades before lowering the wings if they were overlapped in transport. If your tractor has instant on power take-off, engage it at low rpm’s and then slowly increase engine speed to full power take-off speed. If your tractor has instant off power take-off, decrease engine speed slowly to an idle and then disengage power take-off.
A
Alan KirbyAug 1, 2025
How to fix an oil seal leaking on my Land Pride RC2512 Cutter?
- J
  Joseph SotoAug 2, 2025
  If you notice an oil seal leaking on your Land Pride Cutter, drain the oil to the correct level using the fill hole or the full mark on the dipstick if the gearbox is overfilled. Replace damaged seals. Regularly clean off any grass or wire wrapped around the shaft in the seal area.
D
Daniel CallahanAug 7, 2025
What to do if slip clutches slip even with a light load on my Land Pride RC2512?
- M
  mirandarobinsonAug 7, 2025
  If the slip clutches on your Land Pride Cutter slip even with a light load, raise the cutting height to avoid scalping the ground. Adjust the clutch, and if the clutch plates are worn out, replace them. Also, remove any foreign objects caught between the clutch plates.
S
Sara MoodyAug 12, 2025
How to prevent driveline shaft telescoping tube wearing on Land Pride Cutter?
- D
  Deborah MillerAug 12, 2025
  To prevent driveline shaft telescoping tube wearing on your Land Pride Cutter, lubricate it every 8 hours of operation.
S
Sheila TaylorAug 17, 2025
What to do if I have a loose blade carrier on my Land Pride Cutter?
- Z
  Zoe CoxAug 17, 2025
  If you have a loose blade carrier on your Land Pride Cutter, tighten the shaft nut to the specified torque. If it has been running loose in the past, replace the gearbox bearings and/or shaft.
M
Mr. David MckinneyAug 22, 2025
How to prevent blade carrier bent on Land Pride RC2512?
- M
  mariahillAug 22, 2025
  To prevent a bent blade carrier on your Land Pride Cutter, avoid hitting solid objects.

Summary

Important Safety Information

General Safety Practices

General safe operating practices, including shutdown, chains, tires, and maintenance.

Hazard Awareness and Protection

Covers emergencies, PPE, high-pressure fluids, safety lights, ROPS, and rider safety.

Environmental and Utility Safety

Precautions for silica dust, chemicals, and underground utilities.

Safety Labels and Hazards

Explains various safety labels and associated hazards for safe operation.

Section 1: Assembly & Set-up

Tractor Requirements and Setup

Specs for tractors, hydraulic outlets, and drawbar setup.

Pre-Assembly Procedures

Includes shutdown, checklist, and initial steps before assembly.

Component Assembly Steps

Covers torque, unfolding wings, hitch, and driveline assembly.

Connecting to Tractor

Steps for hooking up tractor, driveline, hydraulics, and lights.

Final Assembly Checks

Removing shipping lugs, driveline clearance, purging hydraulics.

Park Jack Assembly

Instructions for attaching and setting up the cutter's park jack.

Section 2: Adjustments

Park Jack and Deck Leveling

Aligning park jack and leveling the center deck.

Wing Deck and Cutting Height Adjustment

Leveling wing decks and adjusting cutter height.

Section 3: Operating Instructions

Pre-Operation Checks

Startup and operating checklists, and safety information.

Operational Guidelines

Tractor turning, inspections, and transport locks.

Field Operations

Transporting, roadside cutting, field setup, and inspection.

Cutter Operation Procedures

Unfolding wings, selecting gear, engaging/disengaging blades.

Clearing Blockages

Steps to safely remove blockages from blade carriers.

Section 4: Options & Accessories

Hitch and Tire Options

Overview of hitch and tire options.

Hydraulic Wing Control Kit

Details of the kit for independent wing hydraulic control.

Section 5: Maintenance & Lubrication

General Maintenance and Systems

General maintenance, hydraulic system, and cutter blades.

Driveline and Clutch Maintenance

Driveline slip clutches, clutch run-in, and disassembly.

Tire and Skid Shoe Maintenance

Tire maintenance and skid shoe replacement.

Storage and Parts

Long-term storage procedures and ordering replacement parts.

Lubrication Points

Identifies all lubrication points and intervals for the implement.

Gearbox and Driveline Lubrication

Lubrication for gearboxes, axle pivots, and driveline joints.

Accessing Driveline Joints

Methods for accessing CV driveline joints for lubrication.

Section 6: Specifications & Capacities

Specifications and Capacities

Detailed specifications and capacities of the RC2512 Series 2.

Dimensional Overview

Diagram showing overall dimensions with a specific cutting height.

Section 7: Features & Benefits

RC2512 Series 2 Features and Benefits

Lists key features and their corresponding benefits.

Section 8: Troubleshooting

Troubleshooting Guide

Lists common problems, causes, and solutions for the rotary cutter.

Section 9: Torque Values & Tire Inflation

Torque Values and Tire Inflation

Charts for bolt torque values and tire inflation pressures.

Section 10: Warranty

Land Pride Warranty Policy

Details Land Pride's warranty terms and conditions.

Land Pride RC2512 Series Specifications

General

Hitch Type	Pull-Type
Driveline Protection	Slip Clutch
Cutting Width	144 inches
Deck Thickness	7 gauge
Blade Carrier Thickness	0.5 in (12.7 mm)
Tires	15 in (38.1 cm)