Land Pride RC5715 - User Manual

Questions and Answers

K
Kara RoweAug 20, 2025
What to do if my Land Pride Cutter has excessive vibration?
- C
  Christopher PalmerAug 20, 2025
  Excessive vibration in your Land Pride Cutter can stem from several issues. It could be due to hitting solid objects, so inspect the area before cutting and avoid them. Other causes include a bent driveline or blade carrier (replace if bent), a broken blade (replace if broken), or blades that won't swing (inspect and unlock them). High torque start-up or hitting solid objects can damage the driveline, so disassemble and inspect it. Also, blades with unequal weight can cause vibration, so replace each pair of blades on the affected carrier.
A
aimee25Aug 22, 2025
Why is the oil seal leaking on my Land Pride Cutter?
- F
  Frank LewisAug 22, 2025
  If the oil seal on your Land Pride Cutter is leaking, it could be due to a few reasons. First, check if the gearbox is overfilled and drain the oil to the fill hole level or the full mark on the dipstick. Damaged seals can also cause leaks, requiring replacement. Additionally, grass or wire wrapped around the shaft in the seal area can be a culprit; clean off any wrapped material and inspect the seal areas regularly.
L
lisa44Aug 23, 2025
Why are the blades breaking on my Land Pride RC5715 Cutter?
- A
  Amy SkinnerAug 25, 2025
  Blades on your Land Pride Cutter might be breaking because you are hitting solid objects. Avoid hitting solid objects to prevent this.
C
Christopher SkinnerAug 26, 2025
What causes driveline yoke or cross failing on my Land Pride RC5715?
- R
  Renee LeeAug 26, 2025
  A driveline yoke or cross failing on your Land Pride Cutter can be attributed to a few reasons. The clutch may be frozen; slip the clutches as per the lubrication instructions. Also, shock loads from hitting solid objects should be avoided. Finally, ensure you lubricate the driveline every 8 hours to prevent failure due to lack of lubrication.
T
Trevor LindseyAug 27, 2025
Why are the blades wearing excessively on my Land Pride RC5715 Cutter?
- N
  Nancy PerezAug 28, 2025
  Excessive blade wear on your Land Pride Cutter can occur if you're cutting on sandy ground; if so, raise the cutting height and consider switching to low lift blades. Also, frequently contacting the ground can cause this issue, so raise the cutting height.
P
Pamela WoodsAug 29, 2025
What to do if the blades are coming loose on my Land Pride RC5715?
- C
  Cynthia GarnerAug 29, 2025
  If the blades on your Land Pride Cutter are coming loose, it could be because they weren't tightened properly. Make sure to tighten the blade hardware. Also, operating the power take-off at excessive speeds can cause this, so ensure you're using the correct power take-off speed.
N
Nicole JonesSep 1, 2025
Why do the Slip Clutches slip even with a light load on my Land Pride RC5715 Cutter?
- R
  Renee Harris DDSSep 1, 2025
  If the slip clutches on your Land Pride Cutter are slipping even with a light load, it could be due to several factors. You might be scalping the ground, so try raising the cutting height. The clutch might not be properly adjusted; adjust it according to the instructions under “Lubrication Points”. Worn-out clutch plates can also cause this issue, requiring replacement. Lastly, a foreign object caught between the clutch plates can cause slipping; remove any foreign objects.
K
Kristen JohnsonSep 3, 2025
Why is the driveline shaft telescoping tube failing on my Land Pride Cutter?
- M
  Mariah WeaverSep 3, 2025
  The driveline shaft telescoping tube on your Land Pride Cutter might be failing due to shock load. Avoid hitting solid objects.
L
Luis DownsSep 4, 2025
What to do if the blades lock-up on my Land Pride RC5715?
- A
  ambercooperSep 5, 2025
  Blades lock-up on your Land Pride Cutter can occur for a few reasons. If the blades were locked together when the wings were folded up, use a pry bar or other tool to separate them before unfolding. If your tractor has instant on power take-off, engage it at low rpm and gradually increase the engine speed. If your tractor has instant off power take-off, disengage the blades at low rpm or switch to a driveline with an over-running clutch.
A
anthony89Sep 7, 2025
Why is the blade carrier loose on my Land Pride RC5715 Cutter?
- C
  Christine GraySep 7, 2025
  A loose blade carrier on your Land Pride Cutter could be due to the blade carrier hardware not being tight enough; tighten the shaft nut to the specified torque. If it has been running loose in the past, you may need to replace the gearbox bearings and/or shaft.

Land Pride RC5715 Specifications

General

Power Requirement	540 RPM
Number of Blades	3
Deck Thickness	10 gauge
Cutting Width	15 ft
Working Width	15 ft
Hitch	Pull-type
Driveline Protection	Slip clutch
Transport Width	72 inches