Land Pride RCM5615 - User Manual

Questions and Answers

J
Julia BenjaminAug 20, 2025
Why is my Land Pride RCM5615 experiencing excessive vibration?
- L
  Luke AllenAug 20, 2025
  Excessive vibration in your Land Pride Cutter can stem from several issues. You might be hitting solid objects, so inspect the area before cutting and avoid them. Other potential causes include a bent driveline or blade carrier (replace them if bent), a broken blade (replace it), or blades that won't swing freely (inspect and unlock them). High torque start-ups or impacts with solid objects can damage the driveline, so disassemble and inspect it for issues like incorrectly located needles or damaged bearing caps. Unequal blade weight can also cause vibration, so replace each pair of blades on the affected carrier.
T
turnerjordanAug 21, 2025
Why are the blades on my Land Pride RCM5615 wearing out so quickly?
- J
  John ThomasAug 22, 2025
  If your Land Pride Cutter blades are wearing excessively, it could be due to several factors. You might be cutting on sandy ground or contacting the ground frequently, so raising the cutting height is recommended. Additionally, operating with a power take-off speed that's too high can cause this issue, so maintain the correct speed by slowing down.
P
Patricia MartinezAug 25, 2025
What to do if driveline yoke or cross failing on Land Pride RCM5615?
- S
  snicholsAug 25, 2025
  If the driveline yoke or cross on your Land Pride Cutter is failing, several factors could be responsible. The clutch may be frozen, so slip the clutches per instructions. Shock loads from hitting solid objects should be avoided. Also, ensure that you lubricate every 8 hours.
A
Angel CampbellAug 26, 2025
Why are the blades on my Land Pride RCM5615 coming loose?
- L
  lauren43Aug 26, 2025
  If the blades on your Land Pride Cutter are coming loose, it could be due to improper tightening. Make sure to tighten the blade hardware. Also, operating the cutter at an excessive power take-off speed can cause loosening, so operate the cutter at the correct speed.
J
Jimmy HerringAug 28, 2025
Why is the oil seal leaking on my Land Pride RCM5615 Cutter?
- D
  David SmithAug 28, 2025
  If the oil seal on your Land Pride Cutter is leaking, it could be due to several reasons. The gearbox might be overfilled, so drain the oil to the correct level. The seals could be damaged, in which case you should replace them. Also, grass or wire wrapped on the shaft in the seal area can cause leaks, so clean off any wrapped material and check the seal areas daily.
S
Steven WoodAug 30, 2025
What to do if blades lock up on Land Pride RCM5615?
- J
  Jody CarterAug 30, 2025
  If the blades on your Land Pride Cutter lock up, it could be due to a few reasons. The blades might be locked together (overlapped) when the wings were raised to the transport position, so use a pry bar or other tool to separate them before lowering the wings. If your tractor has an instant-on power take-off, engage it at low rpms and then slowly increase engine speed to full power take-off speed. Conversely, if your tractor has an instant-off power take-off, decrease engine speed slowly to an idle and then disengage the power take-off.
C
Christopher StanleySep 1, 2025
Why do slip clutches slip even with a light load on Land Pride RCM5615 Cutter?
- C
  coffeyamySep 1, 2025
  If the slip clutches on your Land Pride Cutter slip even with a light load, it could be due to several factors. You might be scalping the ground, so raise the cutting height. The clutch may not be properly adjusted, so adjust it per the instructions. The clutch plates could be worn out, in which case you should replace them. Also, a foreign object caught between the clutch plates can cause slipping, so remove any foreign objects.
D
David HarveySep 2, 2025
What causes a bent blade carrier on Land Pride Cutter?
- D
  Dominic ObrienSep 3, 2025
  If the blade carrier on your Land Pride Cutter is bent, it's likely due to hitting solid objects. Avoid hitting solid objects to prevent this issue.
S
Samuel CantrellSep 5, 2025
Why are the blades breaking on my Land Pride RCM5615?
- W
  William ReyesSep 5, 2025
  If the blades on your Land Pride Cutter are breaking, it's likely due to hitting solid objects. Avoid hitting solid objects to prevent blade breakage.
M
mmcclainSep 7, 2025
What causes excessive side skid wear on Land Pride Cutter?
- D
  Daniel ArnoldSep 7, 2025
  If you're experiencing excessive side skid wear on your Land Pride Cutter, it could be due to abrasive soil or cutting too low. Adjust or raise the cutter height to address this issue.