To Next PageTo Next PageWhy are the blades breaking on my Land Pride Farm Equipment?
If the blades on your Land Pride Farm Equipment are breaking, it's likely due to hitting solid objects. Make sure to avoid hitting solid objects.
Why are the blades wearing excessively on my Land Pride RCD1884?
If the blades on your Land Pride Farm Equipment are wearing excessively, it could be because you're cutting on sandy ground or contacting the ground frequently. In either case, try raising the cutting height.
What to do if the blades are coming loose on my Land Pride RCD1884?
If the blades on your Land Pride Farm Equipment are coming loose, it might be because they weren't tightened properly. Tighten the blade hardware. It could also be due to improper deck attitude; in this case, lower the front of the deck.
What to do if the driveline clutch is slipping on my Land Pride RCD1884?
If the driveline clutch on your Land Pride Farm Equipment is slipping, it might be due to scalping the ground. Try raising the cutting height. It could also be that you are cutting too fast, so reduce your travel speed. Engaging the power take-off too fast at high engine rpm can also cause this, so slowly engage the power take-off at low engine rpm. Finally, avoid cutting over solid objects.
Why is there excessive vibration in my Land Pride RCD1884?
Excessive vibration in your Land Pride Farm Equipment can stem from several issues. The driveline might be bent, requiring replacement. Loose blade bolts should be tightened. A bent blade carrier should be replaced, as should a broken blade. Finally, a blade that won't swing freely should be removed and inspected.
Why is the oil seal leaking on my Land Pride Farm Equipment?
If the oil seal on your Land Pride Farm Equipment is leaking, it could be due to several reasons. The gearbox might be overfilled; if so, drain it to the side plug hole. The seals could be damaged, in which case they should be replaced. Also, check the seal areas daily for grass or wire wrapped on the shaft.
Why is the driveline yoke or cross failing on my Land Pride Farm Equipment?
If the driveline yoke or cross is failing on your Land Pride Farm Equipment, it could be due to a shock load. To prevent this, avoid hitting solid objects. Also, ensure you lubricate every 8 hours to keep it properly maintained.
Why does the blade carrier become loose on my Land Pride RCD1884 Farm Equipment?
If the blade carrier on your Land Pride Farm Equipment becomes loose, it could be due to it running loose in the past. In this case, replace the gearbox output shaft and blade carrier. It could also be that the blade carrier hardware is not tight enough, so tighten it to the specified torque.
Why is the driveline telescoping tube failing on my Land Pride Farm Equipment?
If the driveline telescoping tube is failing on your Land Pride Farm Equipment, it's likely due to a shock load. Make sure to avoid hitting solid objects.
Why is the driveline bent on my Land Pride RCD1884?
If the driveline is bent on your Land Pride Farm Equipment, it could be contacting the frame. Reduce the lift height in the transport position. It could also be contacting the drawbar, so reposition it. Bottoming out can also cause this, so shorten the driveline. Finally, insufficient lubrication can cause binding, so ensure adequate lubrication.
General| Brand | Land Pride |
|---|---|
| Model | RCD1884 |
| Category | Farm Equipment |
| Language | English |
Log for recording model, serial number, and machine specifications.
Fields to record dealer's name, address, and contact details.
Emphasizes careful operation and understanding the manual for accident prevention.
Explains the hazard alert symbol and signal words (DANGER, WARNING, CAUTION).
Guidelines to keep children away from the work area and supervise them.
Procedures for safely shutting down and storing the tractor and implement.
Proper tire inflation, maintenance, and wheel bolt tightening for safety.
Comply with laws, use adequate trailer, maintain safe speed, and avoid overhead lines.
Use a safety chain to control drawn machinery if it separates.
Follow procedures, work safely, use proper tools, and dispose of waste properly.
Be prepared for fires, have first aid, and emergency numbers ready.
Use appropriate clothing and equipment for job safety.
Handle hydraulic fluids with care to prevent serious injury from injection.
Use SMV signs and warning lights when operating on public roads.
Call 811 before digging to locate underground services.
Use seat belt and ROPS for protection against serious injury or death.
Never carry riders on tractor or implement for safety reasons.
Importance, placement, and maintenance of safety labels.
Describes the RCD1884 offset Rotary Cutter's uses and capabilities.
Guidance on how to use the operator's manual for safe and efficient operation.
Information on warranty registration and contacting dealers for service.
Instructions for recording and locating the serial number for service.
Steps to take if you need additional help or are unsatisfied with service.
Specifies tractor horsepower and hitch category requirements for the cutter.
Refers to torque values chart for proper hardware tightening.
Step-by-step instructions for safely uncrating the rotary cutter.
Instructions for installing the vented breather plug on the gearbox.
Detailed steps for assembling the 3-point hitch components.
Guides on connecting the rotary cutter to the tractor's 3-point hitch.
Instructions for attaching the cutter using a quick hitch system.
Instructions for connecting and installing the driveline.
How to check the driveline's collapsible length to prevent damage.
Instructions on how to shorten the driveline if necessary.
How to check for interference between the driveline and tractor/cutter.
Procedures to check the maximum allowable length of the driveline.
Instructions for installing optional replaceable skid shoes.
Recommendation to install front and rear guards for safety.
Instructions for installing standard front corner deflectors.
Instructions for installing the optional front rubber guard.
Instructions for installing the optional front single chain guard.
Instructions for removing the standard rear metal band guard.
Instructions for installing the optional RCD rear extended metal guard.
Overview of primary adjustments for deck leveling and cutting height.
Procedure to ensure the cutter deck is level side-to-side.
How to set the desired cutting height for the rotary cutter.
Adjusting tailwheel height to set rear blade height correctly.
Adjusting the center 3-point link for proper ground contour following.
A checklist of inspections before operating the rotary cutter.
General safety warnings and precautions for operating the cutter.
Inspecting the tractor and cutter before operation.
Guidelines for safely transporting the rotary cutter.
Procedures for safely engaging and disengaging the cutter blades.
Safe practices for operating the cutter in the field.
Step-by-step instructions for safely unhooking the cutter from the tractor.
Comprehensive guidance on safe operation and pre-operation checks.
General advice on maintaining the implement for longevity.
Instructions for inspecting, sharpening, and replacing cutter blades.
How to correctly install and time cutter blades for proper function.
Procedures for checking and adjusting flex coupler and blade timing.
Explanation of the slip-clutch's role in protecting the drivetrain.
Procedures for running in the slip clutch to ensure proper operation.
Detailed steps for disassembling and assembling the slip clutch.
How to maintain and replace accessory skid shoes.
Guidelines for cleaning, servicing, and storing the cutter for long periods.
Information on how to order replacement parts and color codes.
Lubrication legend and intervals for various parts.
Lubrication instructions for the gauge wheel spindle tube.
Lubrication instructions for the gauge wheel hub.
Instructions for checking and filling the gearbox oil level.
Lubrication instructions for the flex coupling shaft.
Lubrication instructions for the driveline U-joints.
Lubrication instructions for driveline shield bearings.
Lubrication instructions for driveline profiles.
Detailed specifications and capacities for the RCD1884 model.
Lists the features and corresponding benefits of the RCD1884 model.
A chart to diagnose and solve common problems with the rotary cutter.
Table of torque values for various bolt sizes and grades.
Specific torque values for Quick Hitch bolt and blade hardware.
Land Pride's warranty terms and conditions for the rotary cutter.
